sfs13ze-m6 Power-One, sfs13ze-m6 Datasheet
sfs13ze-m6
Available stocks
Related parts for sfs13ze-m6
sfs13ze-m6 Summary of contents
Page 1
... Input Model Voltage, Vdc 36-72 SFS13ZA-M6 36-72 SFS13ZB-M6 36-72 SFS13ZD-M6 36-72 SFS13ZE-M6 36-72 SFS08ZG-M6 Model numbers highlighted or shaded are not recommended for new designs. JUN 29, 2006 revised to JUL 01, 2006 SFS DC-DC Series Data Sheet 43W SMT Converter Features • RoHS lead free and lead-solder-exempt products are available • ...
Page 2
... VDC Min Nom Max Units 100 0.9/25 oz/gr Yes 1,127 kHr Min Nom Max Units Basic 1,500 VDC 10 MΩ 1,100 pF Min Nom Max Units VDC 2 5 mADC 20 50 mADC VDC (34) (35) (36) 25.5 27.5 29.5 VDC (31.5) (32.5) (33.5) 90 250 mAp-p μF 1.5 www.power-one.com ...
Page 3
... Iout (A) Page • 1. Output Min Nom Max Units 1.48 1.50 1.52 VDC ADC ± mV 250 μs 500 60 100 mV p-p μF 3,300 110 200 %I max O 650 kHz 0. 1.35 1.65 Vdc Efficiency vs Load Vin Min Vin Nom Vin Max Iout (A) www.power-one.com /°C ...
Page 4
... Iout (A) Page • 1. Output Min Nom Max Units 1.78 1.80 1.82 VDC ADC 250 ± mV μs 500 60 100 mV p-p μF 3,300 110 200 %I max O 650 kHz 0. 1.62 1.98 VDC Efficiency vs Load Vin Min Vin Nom Vin Max Iout (A) www.power-one.com /°C ...
Page 5
... Iout (A) Page • 1. Output Min Nom Max Units 2.47 2.5 2.53 VDC ADC 250 ± mV μs 500 80 130 mV p-p μF 3,300 110 200 %I max O 650 kHz 0. 2.25 2.75 VDC Efficiency vs Load Vin Min Vin Nom Vin Max Iout (A) www.power-one.com /°C ...
Page 6
... Temperature T CO Coefficient Trim Range 1 Below I min the output maintains regulation but output ripple may increase O μ 2 Measured with ceramic capacitor across output pins, as shown on page 9 SFS13ZE Typical Characteristic Curves Vout (V) Output Voltage vs Load 4.0 3.5 3.0 2.5 2.0 1.5 Vin Min 1.0 Vin Nom Vin Max ...
Page 7
... Iout (A) Page • 1. Output Min Nom Max Units 4.94 5.0 5.06 VDC 0 ADC 350 ± mV μs 500 80 130 mV p-p μF 3,300 110 200 %I max O 650 kHz 0. 4.5 5.5 Vdc Efficiency vs Load Vin Min Vin Nom Vin Max Iout (A) www.power-one.com /°C ...
Page 8
... Voltage source or open circuit Vin=Vin.Nom TTL compatible square wave on sync pin. Referenced to –Vin Available compensation Output Power Vs AmbientTemp. and Airflow Ambient Temperature (deg °C) Page SFS DC-DC Series Data Sheet • 1. Output Min Nom Max -1.0 1.0 3.5 6 0.3 700 800 10 www.power-one.com Units VDC VDC mADC kHz % ...
Page 9
... When the output voltage is sensed remotely at the load, the output power from the converter must not exceed maximum rating. multiplying the output voltage (measured at output pins) by the output current. Page • 1. Output limits maximum allowable ( 100°C (see Mechanical C This is determined by www.power-one.com ). To C case ...
Page 10
... SFS13ZB 5010 2516 SFS13ZD 7010 3161 SFS13ZE 11260 4532 SFS08ZG Note: When the output voltage is trimmed up, the output power from the converter must not exceed its maximum rating. This is determined by measuring the voltage on the output pins, and multiplying it by the output current ...
Page 11
... A denotes normal operation, no deviation from specification. B denotes temporary deviation from specification is possible. Page • 1. Output Conducted EMI (Input Terminal) EN55022 A QP. EN55022 A AV 1.E+06 1.E+07 FREQ (MHz) Applied Class Performance Stress Level Outcome * 2KV to 1 pins 3V/m 2 2000Vp 3 to input 3Vrms to 2 input www.power-one.com 1.E+ ...
Page 12
... Failure instructions may result in failure or significant degradation of the modules performance. Power-One will not honor any warranty claims arising from failure to observe these instructions. This product is approved for forced convection reflow soldering only. The curves below define the maximum peak reflow temperature permissible measured on Pins 1 and 10 of the converter ...
Page 13
... Mechanical Drawings Note: Pickup point not central JUN 29, 2006 revised to JUL 01, 2006 SFS DC-DC Series Data Sheet 43W SMT Converter Page • 1. Output Note:- mm[inches] Tolerances: - 0.5-10 ±0.1 10-100 ±0.2 www.power-one.com ...
Page 14
... JUN 29, 2006 revised to JUL 01, 2006 SFS DC-DC Series Data Sheet 43W SMT Converter Recommended Land Pattern Packaging Tray (JEDEC STYLE) Page • 1. Output www.power-one.com ...
Page 15
... The solder exemption refers to all the restricted materials except lead in solder. NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president of Power-One, Inc ...