m62301sp Mitsumi Electronics, Corp., m62301sp Datasheet
m62301sp
Available stocks
Related parts for m62301sp
m62301sp Summary of contents
Page 1
... ANALOG GND ANALOG CONSTANT Vcc CURRENT ANALOG CONTROL GND 0.49V + - 0.36V + DISCHARGE - DECODER GIRDLING 2 MITSUBISHI ELECTRIC M62301SP,FP DIGITAL GND INT 5 16 REFERENCE INPUT 6 15 DIGITAL REFERENCE 8 13 ...
Page 2
... Resistance to determine charge current I Output current I o Note 1.Maximum analog input voltage is less than the difference between Vcc-2.5V as well REF *Charging current MITSUBISHI<Dig.Ana.INTERFACE> M62301SP,FP 10~12-BIT 4CH INTEGRATING A-D CONVERTER Conditions Limits Min Typ 8.0 4.5 5.0 4.5 No more than(Vcc-2.5V) 0 and V No more than(Vcc-2.5V) ...
Page 3
... Note 1.Conversion error;Deviation from the line that links the “0“ scale point (mode 0) and reference scale point (mode 3. V with all channels. Note 2.Linear error;Deviation from the line that links the 0-V input point and 2.5V input point on a given channel. MITSUBISHI<Dig.Ana.INTERFACE> M62301SP,FP 10~12-BIT 4CH INTEGRATING A-D CONVERTER =5.0V,Ta=25°C, unless otherwise noted) DD ...
Page 4
... Note. To ensure discharge from capacitor the above diagram should stay in mode 1 at least for the and REF period calculated above: Tdi=( not necessary to measure T channel. MITSUBISHI ELECTRIC MITSUBISHI<Dig.Ana.INTERFACE> M62301SP, performed.None of these operations ...
Page 5
... RESET output status becomes "L".If voltage increases over 4.50V,the RESET status becomes "H" within 150µsec. MITSUBISHI<Dig.Ana.INTERFACE> 10~12-BIT 4CH INTEGRATING A-D CONVERTER V 50mA OUTPUT UNSETTLED MITSUBISHI ELECTRIC M62301SP, REF 1.22V ...
Page 6
... R 24k I . 1.22V = = . 50µA I 24k MITSUBISHI ELECTRIC MITSUBISHI<Dig.Ana.INTERFACE> M62301SP,FP C :To stabilize reference voltage, REF be sure to connect capacitance of approximately 4700pF. C :We suggest that this capacitance INT be connected to prevent malfunction due to noise. Use C that leaks as slight current I as possible.To prevent leak to the ...
Page 7
... V max+0. 1mA max is 5V. IA MITSUBISHI ELECTRIC MITSUBISHI<Dig.Ana.INTERFACE> M62301SP,FP C :To stabilize reference voltage, REF be sure to connect capacitance of approximately 4700pF. C :We suggest that this capacitance INT be connected to prevent malfunction due to noise. Use CI that leaks as slight current as possible.To prevent leak to the ...
Page 8
... INTEGRATING A-D CONVERTER 2.0 1.0 100 125 0.05 0.04 0.03 0.02 0. (OSR) INT OUTPUT VS.AMBIENT TEMPERATURE 200 100 1 10 INT (mA) O MITSUBISHI ELECTRIC MITSUBISHI<Dig.Ana.INTERFACE> M62301SP,FP ANALOG PART SUPPLY CURRENT VS.SUPPLY VOLTAGE ANALOG Vcc (V) LINEAR ERROR RI=24k RI=12k 0 2.0 2.5 1.0 0 (FSR) ANALOG INPUT RANGE VIA( -20 0 ...
Page 9
... ORE LIMIT RESET VOLTAGE 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 R =2.2k L 0.4 R =100k L 0 0.6 1.0 2.0 RESET VOLTAGE Vcc V (V) RE MITSUBISHI<Dig.Ana.INTERFACE> M62301SP,FP 10~12-BIT 4CH INTEGRATING A-D CONVERTER DETECTION VOLTAGE vs. AMBIENT TEMPERATURE 4.7 4.6 4.5 4.4 4.3 4 -20 AMBIENT TEMPERATURE Ta(°C) DELAY TIME VS.AMBIENT TEMPERATURE 250 200 150 100 -20 AMBIENT TEMPERATURE Ta(°C) MITSUBISHI ELECTRIC ...