SPECIFICATION
OUTPUT SPECIFICATIONS
Voltage adjustability
Remote sense
Regulation, line or load All outputs, NL to FL
Overshoot/undershoot
Transient response
Temperature coefficient
Ripple and noise
Overvoltage protection
Overload protection
Short circuit protection
Thermal protection
Current sharing
Current monitor (V1)
INPUT SPECIFICATIONS
Input voltage range
Input frequency range
Input surge current
Input current
Power factor
Power up time
PAGE 1
[ 2 YEAR WARRANTY ]
Accessible at front panel
at nominal line or all
line variations at FL
Main output
25% step load
change at 1A/µs
0Hz to 20MHz
Reset by cycling AC
90% of rated load
±5.0%
5VDC at full load
3 phase
1 phase (optional)
208VAC, 3 phase
208VAC, 1 phase
3 phase
1 phase
Full load
Open/reverse sense lead protection
All specifications are typical at nominal input, full load at 25°C unless otherwise stated
Compensates for voltage drop
Meets IEEE std. 587.1980;
Auto shutdown, AC reset
of up to 0.5V to the load
105% to 115% full load
50mV pk-pk or 1.0%
None at turn on/off
50% to 100% load
≤5.0% max. dev.,
≤200µs recovery
115% to 130%
180 to 264VAC
180 to 264VAC
3kV ring wave
Auto recovery
±0.2%; 10mV
47Hz to 63Hz
L2000 SERIES
Single output
• Load currents up to 400A
• 3 phase or single phase input
• Shutdown on phase loss
• 3 phase power factor correction
• Single wire current share to 5%
• Ideal for N+1 applications
• Current monitor output included
• UL, CSA, TÜV safety approvals
The L series is a range of single output, high current power supplies ideally suited
to a broad range of applications. Robust performance and field proven reliability
are hallmarks of this series. Field reliability in excess of 100,000 hours has been
documented. The L series will provide stable power for any large electronic
system including telecommunication, data processing and industrial. Typical
applications include broadcast systems, ATM systems and RISC processors and
systems. Semiconductor test equipment, semiconductor and wafer processing
equipment and functional board level testers are other possible applications.
Industrial uses include applications such as laser cutting, water purification,
battery charging, machine control, large scale data logging and optical inspection
equipment. Current sharing, built-in current monitoring, voltage margining and
remote adjustment capability are standard features. Other system interface
features include AC and DC good, OVP, OCP, over temperature protection and
remote enable. Worldwide safety certifications are included.
±0.02%/°C
of nominal
1.0s max.
to 1.0%
±10%
±0.5V
0.94
0.65
20A
8A
EMC CHARACTERISTICS
Radiated noise
Conducted noise
Electrostatic discharge
RF field susceptibility
Electrical fast
transients/bursts
Surge susceptibility
GENERAL SPECIFICATIONS
Hold-up time
Efficiency
Isolation voltage
Switching frequency
Approvals and
standards
Weight
Size
MTBF
ENVIRONMENTAL SPECIFICATIONS
Thermal performance
Cooling
Relative humidity
Altitude
Vibration
EN55022/11, FCC part 15
EN55022/11, FCC part 15
EN61000-4-2
EN61000-4-3
EN61000-4-4
EN61000-4-5
230VAC, 2kW load
230VAC, full load
Input/output
Input/chassis
Output/output
Operating ambient
Non-operating
45CFM
Non-condensing
Operating
Non-operating
5Hz to 500Hz
127 x 203.2 x 279.4 mm
CSA C22.2 No. 234/950
TÜV EN60950, UL1950,
5 x 8 x 11 inches
55,000 feet max.
>100,000 hours
6,000 feet max.
-15°C to +85°C
ball bearing fan
0% to 95% RH
2.4G rms peak
0°C to +50°C
10kg (22Ibs)
Internal DC
25ms min.
3000VAC
1500VAC
500VAC
100kHz
Level A
Level A
Level 3
Level 3
Level 3
Level 3
78%