B10-05 COTO [Coto Technology], B10-05 Datasheet - Page 2

• Manufacturer Part Number: B10-05
• Description: RF Relays
• Manufacturer: COTO [Coto Technology]

Coil Resistance
Nominal Voltage
Must Operate Voltage
Must Release Voltage
Coil Resistance
Nominal Voltage
Must Operate Voltage
Must Release Voltage
Switching Voltage
Switching Current
Carry Current (Continuous)
Contact Rating (Resistive Load)
Life Expectancy
Static Contact Resistance (initial)
Dynamic Contact Resistance (initial)
Insulation Res
Capacitance
Capacitance
Capacitance
Dielectric
Strength
Operate Time
Release Time
RF Insertion Loss
Signal Rise Time (10% - 90%)
NOTES:
1
2
3
4
B10 RF Relays
All parameters specified per EIA/NARM standards
Unless otherwise noted, all parameters are specified
Life expectancies based on characteristic life
Frequency at which the difference between output
for dry reed relays, # RS-421 and RS-436, if a
suitable parametric standard exists.
at 25°C and 40% RH.
(63.2% failure) calculated from the 2-parameter
and input signal amplitude exceeds -3dB. (Direct
wired using 50Ω coaxial cable.)
Weibull distribution. Contact resistance >2.0Ω
defines end of life.
For Most Recent Data, Consult the Coto Technology Website: www.cotorelay.com
Test Parameters
4
Signal Switching
Resistive Load
Other Load Conditions
All Isolated Pins
Across Contacts
Open Contact to Coil
Closed Contact to Coil
Across Contacts
Contact to Coil
Contact to Shield
(including bounce)
(Si diode damped)
3
3
3
Nominal Voltage coil drive @ 30 Hz,
0.5V / 50mA 100 Hz, 1.5 mSec
Corrected for measurement
-3 dB roll-off frequency
system response time
Max DC/Peak AC
Switch and Shield
0.05VDC / 10mA
Shield Guarding
Shield Guarding
Shield Guarding
Consult Factory
12VDC / 10mA
Resistive Load
Conditions
1VDC / 10mA
square wave
3.3V Coil
100VDC
5V Coil
100 µA
100 µA
100 µA
ENVIRONMENTAL RATINGS:
Storage Temperature: -35°C to + 100°C.
Operating Temperature: -20°C to + 85°C.
Vibration: sinusoidal vibration with an amplitude of
10G over a 10Hz to 2000Hz frequency range shall
not cause a closed channel activated at the nominal
coil voltage to open, not an open channel to close.
Max Soldering Temperature: 226°C (438°F) max for
1 minute dwell time. Temperature measured at a
relay ball termination.
1,2
135.0
Min
10!
1500
1500
49.5
10.0
150
0.4
0.4
6
10
E-mail: [e-mail]
150.0
1000
B10
10
Typ
55.0
100
5.0
5.0
0.2
0.5
30
1
1
12
165.0
0.125
0.150
Max
60.5
0.25
125
200
4.0
2.4
6.0
3.8
0.5
3.0
50
40
V (DC/Pk AC)
V (DC/Pk AC)
V (DC/Pk AC)
Volts DC
Volts DC
Volts DC
Volts DC
Volts DC
Volts DC
x 10
x 10
Units
Amps
Amps
Watts
Volts
µSec
µSec
GHz
pSec
pF
pF
pF
Ω
Ω
Ω
Ω
Ω
6
6
Ops
Ops
41