RF3133PCBA RFM [RF Monolithics, Inc], RF3133PCBA Datasheet
RF3133PCBA
Related parts for RF3133PCBA
RF3133PCBA Summary of contents
Page 1
Typical Applications • 3V Quad-Band GSM Handsets • Commercial and Consumer Systems • Portable Battery-Powered Equipment Product Description The RF3133 is a high-power, high-efficiency power ampli- fier module with integrated power control. The device is self-contained with 50 input ...
Page 2
RF3133 Absolute Maximum Ratings Parameter Supply Voltage Power Control Voltage (V ) RAMP Input RF Power Max Duty Cycle Output Load VSWR Operating Temperature Storage Temperature Parameter Min. Power Control V RAMP Power Control “ON” Power Control “OFF” Power Control ...
Page 3
Parameter Min. Overall (GSM850 Mode) Operating Frequency Range Maximum Output Power +33.8 +31.5 Total Current Total Efficiency Input Power Range Output Noise Power Forward Isolation 1 Forward Isolation 2 Cross Band Isolation Second Harmonic Third Harmonic All ...
Page 4
RF3133 Parameter Min. Overall (EGSM900 Mode) Operating Frequency Range Maximum Output Power +34.2 +32.0 Total Efficiency Input Power Range Output Noise Power Forward Isolation 1 Forward Isolation 2 Crossband Isolation Second Harmonic Third Harmonic All other Non-Harmonic ...
Page 5
Parameter Min. Overall (DCS/PCS Mode) Operating Frequency Range Maximum Output Power +32.0 +31.7 +31.0 +29.5 Total Efficiency Input Power Range Output Noise Power Forward Isolation 1 Forward Isolation 2 Second Harmonic Third Harmonic All other Non-Harmonic Spurious Input Impedance Input ...
Page 6
RF3133 Pin Function Description 1 DCS/PCS IN RF input to the DCS band. This BAND Allows external control to select the GSM or DCS band with a logic high or low. A logic low enables the ...
Page 7
PIN #1 DCS/PCS IN BAND SELECT VBATT VRAMP GSM IN Rev A4 030527 Pin Out TX EN VREG 7.00 RF3133 DCS/PCS OUT VCC OUT 10.00 GSM OUT 2-465 ...
Page 8
RF3133 50 strip DCS/PCS IN BAND SELECT TX ENABLE VBATT VREG VRAMP 50 strip GSM IN ** Used to filter noise and spurious from baseband. Evaluation Board Schematic (Download Bill of Materials from www.rfmd.com CON1 50 strip DCS/PCS ...
Page 9
Board Thickness 0.032”, Board Material FR-4, Multi-Layer Rev A4 030527 Evaluation Board Layout Board Size 2.0” x 2.0” RF3133 2-467 ...
Page 10
RF3133 Overview The RF3133 is a quad-band GSM/DCS/PCS power amplifier module that incorporates an indirect closed loop method of power control. This simplifies the phone design by eliminating the need for the complicated control loop design. The indi- rect closed ...
Page 11
Talk time and power management are key concerns in transmitter design since the power amplifier has the highest cur- rent draw in a mobile terminal. Considering only the power amplifier’s efficiency does not provide a true picture for the total ...
Page 12
RF3133 The switching transients due to low battery conditions are regulated by incorporating the following relationship limiting the maximum V voltage (Equation 2). Although no compensation is required for typical battery conditions, the bat- RAMP tery compensation required for extreme ...
Page 13
Switching transients occur when the up and down ramp of the burst is not smooth enough or suddenly changes shape. If the control slope has an inflection point within the output power range or if the slope ...
Page 14
RF3133 PCB Surface Finish The PCB surface finish used for RFMD’s qualification process is Electroless Nickel, immersion Gold. Typical thickness is 3 inch to 8 inch Gold over 180 inch Nickel. PCB Land Pattern Recommendation PCB land patterns are based ...
Page 15
Thermal Pad and Via Design The PCB land pattern has been designed with a thermal pad that matches the exposed die paddle size on the bottom of the device. Thermal vias are required in the PCB layout to effectively conduct ...
Page 16
RF3133 9.00 (mm) Typ. 7.50 (mm) Typ. 6.00 (mm) Typ. 4.50 (mm) Typ. 3.00 (mm) Typ. 1.50 (mm) Typ. Figure 3. Stencil Recommendation 2-474 A = 0.64 (mm) Sq. Typ 0.64 x 0.88 (mm) Typ 0.72 ...