SFP-10GD-SX MRV [MRV Communications, Inc.], SFP-10GD-SX Datasheet

SFP-10GD-SX

Manufacturer Part Number

SFP-10GD-SX

Description

10 Gbps 850 nm Multi-mode SFP+ Transceiver

Manufacturer

MRV [MRV Communications, Inc.]

Datasheet

1.SFP-10GD-SX.pdf (5 pages)

Current page: 1 of 5
Download datasheet (105Kb)

Datasheet

10 Gbps 850 nm Multi-mode SFP+ Transceiver

SFP-10GD-SX

MRV’s SFP-10GD-SX 10Gbps SFP+ transceivers are designed for use in 10-Gigabit Ethernet and 10-Gigabit Fibre Channel links over

multi-mode fi ber. They are compliant with SFF-8431, SFF-8432, and IEEE 802.3ae 10GBASE-SR. Digital Diagnostics functions are

available through a 2-wire serial interface, as specifi ed in SFF-8472. The transceiver is RoHS compliant and lead free as defi ned in Directive

2002/95/EC.

*Exceeding the limits listed in the table may damage the transceiver module permanently

Notes:

Absolute Maximum Ratings*

Parameter

Maximum Supply Voltage

Case Operating Temperature

Storage Temperature

Relative Humidity (Non-Condensing)

Electrical Specifi cations

Parameter

Supply Voltage

Supply Current

Transmitter

Input Diff erential Impedance

Single Ended Data Input Swing

Transmit Disable Voltage

Transmit Enable Voltage

Receiver

Single Ended Data Output Swing

Data Output Rise Time, Fall Time

LOS Fault

LOS Normal

Power Supply Noise Tolerance

Connected directly to TX data input pins. AC coupling from pins into laser driver IC.

20 – 80 % . Measured with Module Compliance Test Board and OMA test pattern. Use of four 1’s and four 0’s in sequence in the

PRBS^9 is an acceptable alternative. SFF-8431 Rev 2.1

LOS is an open collector output. Should be pulled up with 4.7kΩ – 10kΩ on the host board. Normal operation is logic 0; loss of

signal is logic 1. Maximum pull-up voltage is 5.5V.

Testing methodology per SFF-8431. Rev 2.1

Into 100Ω diff erential termination.

V cc T/ V cc R

V out, pp

Symbol

V in, pp

LOS norm

LOS fault

V cc

T A

I cc

T S

Minimum

3.14

-0.5

180

V ee

300

V ee

-40

Per SFF-8431 Rev 2.1

Features

Hot-pluggable SFP+ footprint

Supports 9.95 to 10.52 Gbps bit rates

Power dissipation < 1W

RoHS-6 compliant (lead-free)

Commercial temperature range 0°C to 70°C

Single 3.3 V power supply

Maximum link length of 300 m on 2000 MHZ-km MMF

Uncooled 850 nm VCSEL laser

Receiver limiting electrical interface

Duplex LC connector

Built-in digital diagnostic functions

Typical

100

Maximum

V ee +0.8

V cc

3.46

250

700

850

V cc

4.0

HOST

mVpp

Unit

ºC

Note

Related parts for SFP-10GD-SX

SFP-10GD-SX Summary of contents

Page 1

... Gbps 850 nm Multi-mode SFP+ Transceiver SFP-10GD-SX MRV’s SFP-10GD-SX 10Gbps SFP+ transceivers are designed for use in 10-Gigabit Ethernet and 10-Gigabit Fibre Channel links over multi-mode fi ber. They are compliant with SFF-8431, SFF-8432, and IEEE 802.3ae 10GBASE-SR. Digital Diagnostics functions are available through a 2-wire serial interface, as specifi ed in SFF-8472. The transceiver is RoHS compliant and lead free as defi ned in Directive 2002/95/EC ...

Page 2

Datasheet Pin Descriptions Function Pin V 1 EET T 2 FAULT T 3 DIS SDA 4 SCL 5 MOD_ABS 6 RS0 7 RX_LOS 8 RS1 EER V 11 EER RD EER V ...

Page 3

Datasheet Optical Specifi cations Parameter Transmitter Optical Modulation Amplitude (OMA) Average Launch Power Optical Wavelength RMS Spectral Width Optical Extinction Ratio Transmitter and Dispersion Penalty Average Launch Power of OFF Transmitter Tx Jitter Encircled Flux Relative Intensity Noise Receiver Receiver ...

Page 4

... MRV Corporation upon request. Digital Diagnostics Functions MRV’s SFP-10GD-SX SFP+ transceivers support the 2-wire serial communication protocol as defi ned in the SFF-8472 very closely related to the E2PROM defi ned in the GBIC standard, with the same electrical specifi cations. The standard SFP+ serial ID provides access to identifi cation information that describes the transceiver’s capabilities, standard interfaces, manufacturer, and other information. Additionally, MRV’ ...

Page 5

... Datasheet Mechanical Dimensions Mechanical Specifi cations MRV’s SFP-10GD-SX SFP+ transceivers are compatible with the SFF-8432 specifi cation for improved pluggable form-factor. The bail color is beige. Ordering Information SFP-10GD-SX SFP+ Transceiver Multi-Mode *On 2000 MHZ-km multi-mode ﬁ ber MRV has more than 50 offi ces throughout the world. Addresses, phone numbers and fax numbers are listed at www.mrv.com. ...

Related keywords

SFP-10GD-SX datasheet
SFP-10GD-SX data sheet
SFP-10GD-SX pdf datasheet
SFP-10GD-SX component
SFP-10GD-SX part
SFP-10GD-SX distributor
SFP-10GD-SX RoHS
SFP-10GD-SX datasheet download