pva100p6rq Banner Engineering Corp., pva100p6rq Datasheet
pva100p6rq
Related parts for pva100p6rq
pva100p6rq Summary of contents
Page 1
Compact package size; only 30 mm wide deep (1.2" x .6"). Available in 4 lengths: 100 mm, 225 mm, 300 mm, 375 mm (4", 9", 12", 15") to fit many sizes and/or configurations of parts bins. ...
Page 2
... Receiver PVA100P6 Emitter/Receiver Pair PVA100P6E Emitter PVA100P6R Receiver PVA100N6Q Emitter/Receiver Pair PVA100N6EQ Emitter PVA100N6RQ Receiver PVA100P6Q Emitter/Receiver Pair PVA100P6EQ Emitter PVA100P6RQ Receiver PVA225N6 Emitter/Receiver Pair PVA225N6E Emitter PVA225N6R Receiver PVA225P6 Emitter/Receiver Pair PVA225P6E Emitter PVA225P6R Receiver PVA225N6Q Emitter/Receiver Pair PVA225N6EQ Emitter ...
Page 3
... Receiver: 4-conductor PVC-jacketed 2 m (6.5') cable which is either unterminated or terminated with a 4- Operating Temperature 0° to +50°C (+32° to 122°F) Maximum Off-axis See Figure 4, page 5. Misalignment Certifications Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 PVA Series Parts Verification Array Parts Verfication Array Specifications Standard ...
Page 4
... P/N Includes 4 Stainless steel Phillips panhead machine screws (M4 x 0.7 x 12) 4 Stainless steel hex nuts (M4 x 0.7) 50532 4 Stainless steel lock washers (M4 x 0.7) 1 Plastic screwdriver (3.6 cm/1.4" long) Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 L2 137.8 mm (5.43") 266.4 mm (10.49") 341.4 mm (13.44") 416.6 mm ...
Page 5
... Emitter Receiver Receiver Emitter Figure 2. PVA installation: alternate multiple pairs of emitters and receivers to avoid crosstalk. Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 PVA Series Parts Verification Array Installation Positioning When multiple pairs of sensors are mounted in a confined area, care must be taken to avoid crosstalk between the various sensor pairs ...
Page 6
... Receiver with PNP (Sourcing) Output + 12-30V dc - Job Light Enable* Figure 4. PVA emitter and receiver mounting hardware Emitter with Quick-Disconnect (4-Pin Euro-Style 12-30V Job Light Enable 12-30V Load wh Job Light Enable* Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ...
Page 7
... Switch #4 ON OFF Figure 5. PVA configuration DIP switch setting positions MODE Status Indicator #1 Status Indicator #2 Figure 6. PVA sensor status indicators Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 PVA Series Parts Verification Array Programming PVA Configuration DIP Switch Settings Switch Emitter ...
Page 8
... MQDC-430 9 m (30') P/N 52088 rev. D Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com Figure 8. Align edge of PVA cover To replace the switch cover, align one edge of the cover with the edge of the sensor housing opening (Figure 8). Then press the front corners into place, as shown in Figure 9 ...