DNL10S0A0R16NFD DELTA [Delta Electronics, Inc.], DNL10S0A0R16NFD Datasheet
DNL10S0A0R16NFD
Related parts for DNL10S0A0R16NFD
DNL10S0A0R16NFD Summary of contents
Page 1
Delphi DNL, Non-Isolated Point of Load DC/DC Power Modules: 8.3-14Vin, 0.75-5.0V/16A out The Delphi series DNL, 8.3~14V input, single output, non-isolated point of load DC/DC converters are the latest offering from a world leader in power systems technology and manufacturing ...
Page 2
... Module On, Ion/off Module Off, Ion/off Module On, Von/off Module Off, Von/off Module On, Ion/off Module Off, Ion/off Delay from Vin.min to application of tracking voltage Power-up, subject to 2V/mS Power-down, subject to 1V/mS Io=80%Io, max, Ta=25℃ Refer to Figure 31 for the measuring point DNL10S0A0R16NFD Min. Typ. Max. Units 0 15 Vdc 0 Vin,max Vdc ...
Page 3
ELECTRICAL CHARACTERISTICS CURVES LOAD (A) Figure 1: Converter efficiency vs. output current (0.75V output voltage LOAD ...
Page 4
ELECTRICAL CHARACTERISTICS CURVES 100 LOAD (A) Figure 7: Converter efficiency vs. output current (5.0V output voltage) Figure 8: Output ripple & noise at 12Vin, 2.5V/16A out Vin Vo Figure ...
Page 5
ELECTRICAL CHARACTERISTICS CURVES Remote On/Off Vo Figure 12: Turn on Using Remote On/Off with external capacitors (Co= 5000 µF), 5.0V/16A out Figure 13: Typical transient response to step load change at 2.5A/µS from 100% to 50% of Io, max at ...
Page 6
TEST CONFIGURATIONS TO OSCILLOSCOPE L 2 100uF BATTERY Tantalum Note: Input reflected-ripple current is measured with a simulated source inductance. measured at the input of the module. Figure 17: Input reflected-ripple test setup COPPER STRIP Vo Resistive 10uF 1uF SCOPE ...
Page 7
DESIGN CONSIDERATIONS (CON.) The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the module. An input capacitance must be placed close to the modules input pins to filter ...
Page 8
FEATURES DESCRIPTIONS (CON.) Over-Temperature Protection The over-temperature protection consists of circuitry that provides protection from thermal damage. If the temperature exceeds the over-temperature threshold the module will shut down. The module will try to restart after shutdown. If the over-temperature ...
Page 9
FEATURE DESCRIPTIONS (CON. Table 1 provides Rtrim values required for some common output voltages, while Table 2 provides values of external voltage source, Vtrim, for the same common output voltages. By using a 1% tolerance trim resistor, set point tolerance ...
Page 10
FEATURE DESCRIPTIONS (CON. The output voltage tracking feature (Figure 27 to Figure 29) is achieved according to the different external connections. If the tracking feature is not used, the TRACK pin of the module can be left unconnected or tied ...
Page 11
FEATURE DESCRIPTIONS (CON. Sequential Start-up Sequential start-up (Figure 27) is implemented by placing an On/Off control circuit between Vo PS1 of PS2. PS1 Vin Vo PS1 On/Off R2 C1 Simultaneous Simultaneous tracking (Figure 28) is implemented by ...
Page 12
THERMAL CONSIDERATIONS Thermal management is an important part of the system design. To ensure proper, reliable operation, sufficient cooling of the power module is needed over the entire temperature range of the module. Convection cooling is usually the dominant mode ...
Page 13
THERMAL CURVES Figure 31: Temperature measurement location * The allowed maximum hot spot temperature is defined at 125 DNL10S0A0R16(Standard) Output Current vs. Ambient Temperature and Air Velocity @ Vin = 12V 3.3V (Either Orientation) Output Current( ...
Page 14
MECHANICAL DRAWING SMD PACKAGE (OPTIONAL) DS_DNL10SIP16_01262007 SIP PACKAGE 14 ...
Page 15
... MODEL LIST Model Name Packaging Input Voltage DNL10S0A0S16PFD SMD 8.3V ~ 14V DNL10S0A0S16NFD SMD 8.3V ~ 14V DNL10S0A0R16PFD SIP 8.3V ~ 14V DNL10S0A0R16NFD SIP 8.3V ~ 14V CONTACT: www.delta.com.tw/dcdc USA: Telephone: East Coast: (888) 335 8201 West Coast: (888) 335 8208 Fax: (978) 656 3964 Email: DCDC@delta-corp.com WARRANTY Delta offers a two (2) year limited warranty ...