C-13-2500-FDFB-SLC4 SOURCE [Source Photonics, Inc.], C-13-2500-FDFB-SLC4 Datasheet
C-13-2500-FDFB-SLC4
Related parts for C-13-2500-FDFB-SLC4
C-13-2500-FDFB-SLC4 Summary of contents
Page 1
... Total Jitter TJ 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 LUMINENTOIC.COM 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2.5 Gbps Single Mode SFF LC Transceiver C-1X-2500(C)-FDFB-SLC4 Features • Duplex LC Single Mode Transceiver • ...
Page 2
... Signal Detect Output Voltage-High V SDH- 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 LUMINENTOIC.COM 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2.5 Gbps Single Mode SFF LC Transceiver C-1X-2500(C)-FDFB-SLC4 Min Typical Max ...
Page 3
... They are isolated from circuit ground. 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 LUMINENTOIC.COM 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2.5 Gbps Single Mode SFF LC Transceiver C-1X-2500(C)-FDFB-SLC4 Notes ...
Page 4
... Inputs to the C-1X-2500(C)-FDFB-SLC4 series transmitters are AC coupled and internally terminated through 50 ohms to AC ground. These transceivers can operate with LVPECL or CML logic levels. The input signal must have at least a 200 mV peak to (single ended) signal swing. Output from the receiver section of the module is also AC coupled and is expected to drive into 50 ohm load. Different termination strategies may be required depending on the particular Serializer / Deserializer chip set used ...
Page 5
... Signal Detect The C-1X-2500(C)-FDFB-SLC4 transceivers are equipped with LVTTL / LVPECL signal detect outputs. The standard LVTTL output eliminates the need for a LVPECL to LVTTL level shifter in most in most applications. 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 LUMINENTOIC.COM 9F, No 81, Shui Lee Rd. • ...
Page 6
... The mounting posts are at case ground and should not be connected to circuit ground. The mounting posts are at case ground and should not be connected to circuit ground. The ferrite bead should provide a real impedance 100 ohms at 100 to 1000 MHz. Bypass capacitors should be placed as close to the 10-pin connector as possible. ...
Page 7
... LuminentOIC transceivers offer a metalized plastic case and a special chassis grounding clip. As shown in the drawing, this clip connects the module case to chassis ground then installed flush through the panel cutout. The grounding clip in this way brushes the edge of the cutout in order to make a proper contact. The use of a grounding clip also provides increased electrostatic protection and helps reduce radiated emissions from the module or the host circuit board through the chassis faceplate ...
Page 8
... Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 LUMINENTOIC.COM 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2.5 Gbps Single Mode SFF LC Transceiver C-1X-2500(C)-FDFB-SLC4 ...
Page 9
... MOUNTING STUDS SHOULD BE SOLDERED TO CHASSIS GROUND FOR MECHANICAL INTEGRITY. Recommended Panel mounting DIMENSION IN MILLIMETER (INCHES) 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 LUMINENTOIC.COM 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2.5 Gbps Single Mode SFF LC Transceiver C-1X-2500(C)-FDFB-SLC4 9 LUMNDS814-Apr2605 ...
Page 10
... Ordering Information Available Options: C-13-2500-FDFB-SLC4 C-13-2500C-FDFB-SLC4 C-15-2500-FDFB-SLC4 C-15-2500C-FDFB-SLC4 Part numbering Definition: • Wavelength 1310 Wavelength 1550 nm • Communication protocol 2500 = LVPEVL SD Output 2500C = LVTTL SD Output • +3.3V SFF Transceiver, DFB • Single mode fiber • Connector options • Power dBm Warnings: Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD) ...