UPC2766GS-E1 NEC [NEC], UPC2766GS-E1 Datasheet
UPC2766GS-E1
Related parts for UPC2766GS-E1
UPC2766GS-E1 Summary of contents
Page 1
WIDE BAND IQ DEMODULATOR FOR DIGITAL VIDEO/DATA RECEIVER DESCRIPTION The PC2766GR/ Silicon monolithic IC designed for use as IQ demodulator in wide dynamic range compressed video or spread spectrum receivers. This IC consists of a wide band RF ...
Page 2
INTERNAL BLOCK DIAGRAM I out I out GND IF I-IF Amp. I-Lo.Buff.Amp I-MIX trim Vcc Vcc IF GND Q out Q out ...
Page 3
PIN FUNCTIONS PIN VOLTAGE PIN No. PIN NAME TYP. ( Trim 4.2 Trimming pin for I-IF output 5.0 Power supply pin for I-MIXER 5.0 Power supply pin for RF and ...
Page 4
PIN VOLTAGE PIN No. PIN NAME TYP. (V) 11 Qout 3.3 Q-IF output pin. 11 pin and 12 pin are balance outputs. 12 Qout 3.3 13 GNDIF Q 0.0 Ground pin of Q-IF block 2.2 Oscillator signal ...
Page 5
ABSOLUTE MAXIMUM RATINGS (T PC2766GR PARAMETER SYMBOL Supply voltage Power dissipation Operating temperature range Storage temperature range PC2766GS PARAMETER SYMBOL Supply voltage Power dissipation Operating temperature range Storage temperature range Note 1 Mounted 1.6 mm double epoxy ...
Page 6
ELECTRICAL CHARACTERISTICS (V PC2766GR/GS PARAMETER SYMBOL Supply current RF input bandwidth output bandwidth IF BW Gain control range IQ phase balance IQ amplitude balance Output voltage Conversion gain STANDARD CHARACTERISTICS (REFERENCE VALUES) (V PC2766GR/GS PARAMETER SYMBOL Noise ...
Page 7
TYPICAL CHARACTERISTICS – on Measurement Circuit – (Note 2 Lower local) CG vs. f (Iout MHz dBm Vagc = 0 V Note ˚C T ...
Page 8
IQ PHASE BALANCE vs ˚ ˚ MHz dBm dBm P LO ...
Page 9
IM vs. Vagc (Iout 480 MHz RF1 f = 490 MHz RF2 f = 440 MHz Pin = _ 20 dBm each = _ 10 dBm ...
Page 10
MEASUREMENT CIRCUIT (@ Z = 250 ) L I out 200 Note 300 nH 250 1 000 pF 1 000 I-IF Amp. I-Lo.Buff.Amp I-MIX 000 pF 1 000 pF ...
Page 11
APPLICATION CIRCUIT EXAMPLE I out I out LPF LPF 1 000 pF 1 000 I-IF Amp. I-Lo.Buff.Amp. I-MIX 000 pF 1 000 pF 1 000 Bias Trim OSC ...
Page 12
PACKAGE DIMENSIONS 20 PIN PLASTIC SSOP (225 mil) (UNIT: mm 6.7 0.3 1.8 MAX. 1.5 0.1 0.15 0.65 +0.10 0.10 M 0.22 –0.05 0.1 0.1 NOTE Each lead centerline is located within 0. its true position ...
Page 13
PIN PLASTIC SOP (300 mil) (UNIT: mm 12.7 0.3 1.55 0.1 1.27 0.4 0.1 0.12 M 0.1 0.1 1.8 MAX. NOTE Each lead centerline is located within 0. its true position (T.P.) at maximum material ...
Page 14
RECOMMENDED SOLDERING CONDITIONS The following conditions (see table below) must be met when soldering this product. Please consult with our sales offices in case other soldering process is used or in case soldering is done under different conditions. For details ...
Page 15
Data Sheet P10193EJ4V0DS00 PC2766GR/GS 15 ...
Page 16
The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. No part of this document may be copied or reproduced in any form or by any means ...