MAX6841 MAXIM [Maxim Integrated Products], MAX6841 Datasheet
MAX6841
Related parts for MAX6841
MAX6841 Summary of contents
Page 1
... The active-low open-drain reset output requires a pullup resistor that can be connected to a voltage from The low supply current (5.7µA) and small package (SOT23-5) make the MAX6841–MAX6845 ideal for use in portable equipment. Computers Controllers Intelligent Instruments Critical µP and µC Power Monitoring ...
Page 2
... SOT23 (derate 7.1mW/°C above +70°C)............571mW Operating Temperature Range ...........................-40°C to +85°C Junction Temperature ......................................................+150°C + 0.3V) CC Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10s) .................................+300°C CONDITIONS MAX6843/MAX6845 CC MAX6841/MAX6842/MAX6844 (Note 0.9V, no load, reset not asserted 1.5V, no load, reset not asserted ...
Page 3
... SOURCE asserted V OH ≥ 0.83V 40µA, reset CC SOURCE asserted ≥ 0.83V 80µA, reset not CC SINK V OL asserted = 0.55V (MAX6841/MAX6842). CC(MIN) > 0.833V -40°C to +85° Typical Operating Characteristics POWER-DOWN RESET DELAY vs. TEMPERATURE 350 300 V = 10mV OD 250 V = 20mV OD 200 ...
Page 4
... TEMPERATURE (°C) Push-Pull (MAX6841) or Open-Drain (MAX6842) Active-Low Reset Output. RESET changes from high to low when pulled low. RESET remains low for the reset timeout period after V exceeds the device reset threshold and MR is released high. Push-Pull (MAX6843) or Open-Drain (MAX6845) Active-Low Reset Output. RESET changes from high to low when RESET IN drops below the 187 ...
Page 5
... TIMEOUT PERIOD GND Detailed Description A microprocessor’s (µP’s) reset input starts the µ known state. The MAX6841–MAX6845 assert a reset dur- ing power-up, power-down, and brownout conditions. When the V supply voltage falls below a preset thresh- CC old (MAX6841/MAX6842) or RESET IN falls below the ...
Page 6
... CC-TH 100kΩ, then R1 = 26.3kΩ. Applications Information V Falling Transients CC The MAX6841–MAX6845 are relatively immune to short- duration falling V transients (glitches). Figure 2 CC shows typical transient duration vs. reset comparator overdrive, for which the MAX6841–MAX6845 do not generate a reset pulse. The graph was generated using a falling pulse applied starting 0 ...
Page 7
... V CC µP RESET GND Table 2. Active Timeout Period Guide SUFFIX Table 3. Standard Versions DEVICE CC MAX6841HUKD0 MAX6841HUKD3 MAX6841FUKD0 MAX6841FUKD3 MAX6841DUKD0 MAX6841DUKD3 MAX6842HUKD0 MAX6842HUKD3 MAX6842FUKD0 MAX6842FUKD3 MAX6842DUKD0 MAX6842DUKD3 MAX6843UKD0 MAX6843UKD3 MAX6844UKD0 MAX6844UKD3 MAX6845UKD0 MAX6845UKD3 Voltage Detectors RESET THRESHOLD (V) I 1.388 H 1.313 G 1 ...
Page 8
... Ultra-Low-Voltage µP Reset Circuits and Voltage Detectors PART MANUAL RESET ✔ MAX6841 ✔ MAX6842 ✔ MAX6843 ✔ MAX6844 ✔ MAX6845 Typical Operating Circuit V IN 3.3V 0.9V DC/DC CONVERTER V CC MAX6842D/E RESET PUSHBUTTON MR RESET SWITCH GND 8 _______________________________________________________________________________________ ADJUSTABLE PUSH-PULL RESET RESET INPUT ✔ — — ...
Page 9
Ultra-Low-Voltage µP Reset Circuits and (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information www.maxim-ic.com/packages.) Maxim cannot assume responsibility for use of any circuitry other than circuitry ...