PIC12F1822 MICROCHIP [Microchip Technology], PIC12F1822 Datasheet - Page 42

• Manufacturer Part Number: PIC12F1822
• Description: 8/14-Pin Flash Microcontrollers with nanoWatt XLP Technology
• Manufacturer: MICROCHIP [Microchip Technology]

PIC12F/LF1822/16F/LF1823
3.3
The Program Counter (PC) is 15 bits wide. The low byte
comes from the PCL register, which is a readable and
writable register. The high byte (PC<14:8>) is not directly
readable or writable and comes from PCLATH. On any
Reset, the PC is cleared. Figure 3-3 shows the five
situations for the loading of the PC.
FIGURE 3-3:
3.3.1
Executing any instruction with the PCL register as the
destination simultaneously causes the Program Coun-
ter PC<14:8> bits (PCH) to be replaced by the contents
of the PCLATH register. This allows the entire contents
of the program counter to be changed by writing the
desired upper 7 bits to the PCLATH register. When the
lower 8 bits are written to the PCL register, all 15 bits of
the program counter will change to the values con-
tained in the PCLATH register and those being written
to the PCL register.
3.3.2
A computed GOTO is accomplished by adding an offset to
the program counter (ADDWF PCL). When performing a
table read using a computed GOTO method, care should
be exercised if the table location crosses a PCL memory
boundary (each 256-byte block). Refer to the Application
Note AN556, “Implementing a Table Read” (DS00556).
DS41413A-page 42
PCLATH
PCLATH
PCLATH
PC
PC
PC
PC
PC
PCL and PCLATH
14
14
14
14
14
MODIFYING PCL
COMPUTED GOTO
6
6
6
4
PCH
PCH
PCH
PCH
PCH
7
7
PC + OPCODE <8:0>
LOADING OF PC IN
DIFFERENT SITUATIONS
PC + W
15
15
0
0
0
OPCODE <10:0>
11
ALU Result
8
PCL
PCL
PCL
PCL
PCL
8
W
0
0
0
0
0
Instruction with
GOTO, CALL
Destination
CALLW
BRW
BRA
PCL as
Preliminary
3.3.3
A computed function CALL allows programs to maintain
tables of functions and provide another way to execute
state machines or look-up tables. When performing a
table read using a computed function CALL, care
should be exercised if the table location crosses a PCL
memory boundary (each 256-byte block).
If using the CALL instruction, the PCH<2:0> and PCL
registers are loaded with the operand of the CALL
instruction. PCH<6:3> is loaded with PCLATH<6:3>.
The CALLW instruction enables computed calls by com-
bining PCLATH and W to form the destination address.
A computed CALLW is accomplished by loading the W
register with the desired address and executing CALLW.
The PCL register is loaded with the value of W and
PCH is loaded with PCLATH.
3.3.4
The branching instructions add an offset to the PC.
This allows relocatable code and code that crosses
page boundaries. There are two forms of branching,
BRW and BRA. The PC will have incremented to fetch
the next instruction in both cases. When using either
branching instruction, a PCL memory boundary may be
crossed.
If using BRW, load the W register with the desired
unsigned address and execute BRW. The entire PC will
be loaded with the address PC + 1 + W.
If using BRA, the entire PC will be loaded with PC + 1 +,
the signed value of the operand of the BRA instruction.
COMPUTED FUNCTION CALLS
BRANCHING
 2010 Microchip Technology Inc.