MAX473-MAX475 MAXIM [Maxim Integrated Products], MAX473-MAX475 Datasheet
MAX473-MAX475
Related parts for MAX473-MAX475
MAX473-MAX475 Summary of contents
Page 1
... Rev 1; 3/95 _______________General Description The single MAX473, dual MAX474, and quad MAX475 are single-supply (2.7V to 5.25V), unity-gain-stable op amps with rail-to-rail output swing. Each op amp guar- antees a 10MHz unity-gain bandwidth, 15V/µs slew rate, and 600Ω drive capability while typically consum- ing only 2mA supply current ...
Page 2
... MAX47_MJ_ ...................................................-55°C to +125°C Junction Temperatures MAX47_C_ _/E_ _........................................................ +150°C MAX47_MJ_ ................................................................ +175°C Storage Temperature Range .............................-65°C to +160°C Lead Temperature (soldering, 10sec) .............................+300°C = 0.5V +25°C, unless otherwise noted.) OUT A CONDITIONS MAX473 MAX474 MAX475 Current flows out of terminals High Low ≤ V ≤ 1.9V) EE ...
Page 3
... 10kΩ 20pF Per amplifier Single supply Dual supplies = 0.5V 0°C to +70°C, unless otherwise noted.) OUT A CONDITIONS MAX473 MAX474 MAX475 Current flows out of terminals ≤ V ≤ 1.9V 2.7V to 6.0V CC 0.4V ≤ V ≤ 10kΩ L OUT ( ...
Page 4
... C = 20pF +1V step IN IN Per amplifier Single supply Dual supplies = 0.5V -55°C to +125°C, unless otherwise noted.) OUT A CONDITIONS MAX473 MAX474 MAX475 Current flows out of terminals ≤ V ≤ 2.15V 2.7V to 6.0V CC 0.5V ≤ V ≤ 10kΩ ...
Page 5
Operating Characteristics ( +25°C, unless otherwise noted SUPPLY CURRENT PER AMPLIFIER vs. SUPPLY VOLTAGE 3.0 2.5 2.0 1.5 1 (V) ...
Page 6
Single/Dual/Quad, 10MHz Single-Supply Op Amps ____________________________Typical Operating Characteristics (continued 5V 0V +25°C, unless otherwise noted MINIMUM OUTPUT VOLTAGE vs. TEMPERATURE ...
Page 7
Operating Characteristics (continued 5V 0V +25°C, unless otherwise noted POWER-SUPPLY REJECTION RATIO vs. FREQUENCY ± 300mV ± 250mV ...
Page 8
Single/Dual/Quad, 10MHz Single-Supply Op Amps ____________________________Typical Operating Characteristics (continued 5V 0V +25°C, unless otherwise noted SMALL-SIGNAL TRANSIENT RESPONSE (V = 5V) CC 200ns/div ...
Page 9
... Minimizing Offsets The MAX473’s maximum offset voltage is ±2mV (T = +25°C). If additional offset adjustment is required, A connect a 2kΩ trim potentiometer between pins 1, 8, and 4 (Figure 1). Input offset voltage for the dual MAX474 and quad MAX475 cannot be externally trimmed ...
Page 10
... When driving large capacitive loads, add an output iso- lation resistor, as shown in Figure 4. This resistor improves the phase margin by isolating the load capacitance from the amplifier output. Figure 5 shows the MAX473/MAX474/MAX475 driving a capacitive load of 1000pF using the circuit of Figure 4. Feedback Resistors The feedback resistors appear as a resistance network to the op amp’ ...
Page 11
... OUT where the slew rate (SR) is 15V/µs min. Figure 6 shows the full-power bandwidth as a function of the peak-to- peak AC output voltage. ______________________________________________________________________________________ Single/Dual/Quad, 10MHz Single-Supply Op Amps Figure 5. The MAX473 easily drives 1000pF using the Capacitive-Load Driving Circuit (Figure 4). 100 10 MAX475 V OUT ...
Page 12
... SUBSTRATE CONNECTED TO V OUTD OUTA IND- IND INA- INC+ INC- INA+ OUTC TRANSISTOR COUNT: 355 SUBSTRATE CONNECTED TO V Printed USA is a registered trademark of Maxim Integrated Products. MAX473 NULL V CC 0.065" (1.651mm) OUT 0.052" (1.321mm) EE MAX474 V CC OUTB INB- 0.084" (2.134mm) ...