EL7563CM-T13 ELANTEC [Elantec Semiconductor], EL7563CM-T13 Datasheet
EL7563CM-T13
Related parts for EL7563CM-T13
EL7563CM-T13 Summary of contents
Page 1
... DC:DC converter modules • GTL + Bus power supply Ordering Information Tape & Part No Package Reel Outline # EL7563CM 20-Pin SO (0.300”) - MDP0027 EL7563CM-T13 20-Pin SO (0.300”) 13” MDP0027 EL7563CRE-T7 28-Pin HTSSOP 7” MDP0048 EL7563CRE-T13 28-Pin HTSSOP 13” MDP0048 Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation. © ...
Page 2
EL7563C Monolithic 4 Amp DC:DC Step-down Regulator Absolute Maximum Ratings Supply Voltage between and GND Voltage LX Input Voltage V Voltage HI Important Note: All parameters having Min/Max specifications are guaranteed. Typ values are ...
Page 3
Closed Loop AC Electrical Characteristics 3.3V 25° 1.2nF, unless otherwise specified OSC Parameter Description F Oscillator Initial Accuracy OSC t Minimum Oscillator Sync Width SYNC M ...
Page 4
EL7563C Monolithic 4 Amp DC:DC Step-down Regulator Pin Descriptions Pin Number Pin Name 1 VREF Bandgap reference bypass capacitor; typically 0.1µF to SGND 2 SGND Control circuit negative supply or signal ground 3 COSC Oscillator timing capacitor (see performance curves) ...
Page 5
Typical Performance Curves (20-Pin SO Package) *Note: The 28-Pin HTSSOP Package Offers Improved Performance *Efficiency =3.3V IN 100 V =2.5V V =1. =1. = ...
Page 6
EL7563C Monolithic 4 Amp DC:DC Step-down Regulator Typical Performance Curves *Note: The 28-Pin HTSSOP Package Offers Improved Performance Switching Frequency vs C OSC 1000 900 800 700 600 500 400 300 200 100 100 200 300 400 500 600 700 ...
Page 7
Typical Performance Curves Power-Down V =3.3V, V =1.8V Disable V =3.3V, V =1. Monolithic 4 Amp DC:DC Step-down Regulator Enable V =3.3V, V =1.8V ...
Page 8
EL7563C Monolithic 4 Amp DC:DC Step-down Regulator Block Diagram VTJ Junction Temperature 2.2nF Controller Supply 22 VDD 3.3V 0.22µF EN STP Power Tracking STN SGND FB 0.1µF 390pF VREF COSC Voltage VDRV Oscillator Reference VHI VIN Power FET PWM Drivers ...
Page 9
Applications Information Circuit Description General The EL7563C is a fixed frequency, current mode con- trolled DC:DC converter with integrated N-channel power MOSFETs and a high precision reference. The device incorporates all the active circuitry required to implement a cost effective, ...
Page 10
EL7563C Monolithic 4 Amp DC:DC Step-down Regulator high-side switch remains on until all four comparator inputs have summed to zero, at which time the high-side switch is turned off and the low-side switch is turned on. However, the maximum on-duty ...
Page 11
T (°C) can be deducted from the J following relation: 1.2 VTJ – ----------------------- - 0.00384 Where VTJ is the voltage at VTJ pin in volts. Power Good and Power On Reset During ...
Page 12
EL7563C Monolithic 4 Amp DC:DC Step-down Regulator 2. Offset Tracking The intended start-up sequence is shown in Figure 3a. In this configuration, V will not start until V C preset value of ------------------- - ...
Page 13
The second way of offset tracking is to use the EN and Power Good pins, as shown in Figure 4. In this configu- ration, V does not have to be larger than ...
Page 14
EL7563C Monolithic 4 Amp DC:DC Step-down Regulator 3. External Soft Start An external soft start can be combined with auxilliary supply tracking to provide desired soft start other than internally preset soft start (Figure 5). The appropriate start-up time is: ...
Page 15
Start-up Delay A capacitor can be added to the EN pin to delay the con- verter start-up (Figure 6) by utilizing the pull-up current. The delay time is approximately 1200 ...
Page 16
... This conductive heat path MUST then be connected to a heat sinking area on the PCB in order to dissipate heat out and away from the device. The conductive paths for the EL7563CM package are the fused leads 11, 12, and 13 sufficient amount of PCB metal area is connected to the fused package leads, a junction-to-ambient resistance of 43° ...
Page 17
Package Outline Drawing NOTE: The package drawing shown here may not be the latest version. For the latest revision, please refer to the Elan- tec website at http://www.elantec.com/pages/package_outline.html Monolithic 4 Amp DC:DC Step-down Regulator 17 EL7563C ...
Page 18
EL7563C Monolithic 4 Amp DC:DC Step-down Regulator General Disclaimer Specifications contained in this data sheet are in effect as of the publication date shown. Elantec, Inc. reserves the right to make changes in the cir- cuitry or specifications contained herein ...