RT9172 RICHTEK [Richtek Technology Corporation], RT9172 Datasheet - Page 8

• Manufacturer Part Number: RT9172
• Description: 3A FIXED OUTPUT VOLTAGE LDO REGULATOR
• Manufacturer: RICHTEK [Richtek Technology Corporation]

RT9172
Functional Description
Capacitor Selection
The RT9172 requires a minimum input capacitance of
1µF between the input and ground pins to prevent any
impedance interactions with the supply. The RT9172
requires a minimum of 10µF (tantalum, or electrolytic)
capacitance between the output and ground pins for
proper operation, if used 10µF ceromic please parrell
with 100µF tantalum or electrolytic. Larger capacitance
provides better load dynamics and noise performance.
Error Operation (FLG)
The RT9172 produces a logic low signal at the FLG pin
when the output drops out of regulation due to low input
voltage, current limiting, or thermal limiting.
The internal error FLG comparator has an open drain
output stage. Hence, the FLG pin should be pulled high
through a pull up resistor.
Sense Pin
In applications where the regulator output is not very
close to the load, RT9172 can provide better remote
load regulation using the SENSE pin. Fig.2 and Fig.3
depict the advantage of the SENSE option. RT9172
regulates the voltage at the output pin. Hence, the
voltage at the remote load will be the regulator output
voltage minus the drop across the trace resistance. For
example, in the case of a 3.3V output, if the trace
resistance is 100mΩ, the voltage at the remote load will
be 3V with 3A of load current, I
regulates the voltage at the sense pin. Connecting the
sense pin to the remote load will provide regulation at
the remote load, as shown in Fig.2 and Fig.3.
Chip Enable Operation
A CMOS logic level signal at the chip enable (EN) pin
will turn-off the regulator. Pin EN must be actively
terminated through a 10kΩ pull-up resistor for a proper
operation. If this pin is driven from a source that actively
pulls high and low (such as a CMOS rail to rail
comparator), the pull-up resistor is not required. This
pin must be tied to V
www.richtek-ic.com.tw
8
IN
if not used.
LOAD
. The RT9172
Preliminary
Dropout Voltage
The dropout voltage of a regulator is defined as the
minimum input-to-output differential required to stay
within 2% of the output voltage. The RT9172 uses an
internal MOS-FET with an R
CMOS LDOs, the dropout voltage is the product of the
load current and the R
Maximum Output Current Capability
RT9172 can deliver a continuous current of 1.5 A over
the full operating temperature range. A heatsink may
be required depending on the maximum power
dissipation and maximum ambient temperature of the
application. Under all possible conditions, the junction
temperature must be within the range specified under
operating conditions. The total power dissipation of
the device is given by:
PD = (V
where I
device (specified under Electrical Characteristics).
The maximum allowable temperature rise (T
depends on the maximum ambient temperature
(T
allowable junction temperature (T
T
The maximum allowable value for junction to ambient
Thermal Resistance, θ
The maximum allowable value for junction to ambient
Thermal Resistance, θ
formula:
θ
RT9172 are available in TO-220, TO-263, and SOT-
223 packages. The thermal resistance depends in
amount of copper area or heat sink, and on air flow. If
the maximum allowable value of θ
is ≧ 60
TO-263 package, and ≧140
package, no heatsink is needed since the package
can
requirements. If the value for allowable θ
these limits, a heat sink is required.
JA
RMAX
AMAX
= T
dissipate
RMAX
= T
) of the application, and the maximum
GND
IN
°
- V
JMAX
C/W for TO-220 package, ≧ 60
is the operating ground current of the
/ P
OUT
D
– T
) I
enough
OUT
AMAX
DS(ON)
JA
JA
+ (V
, can be calculated using the
= T
IN
heat
RMAX
) I
of the internal MOSFET.
GND
DS(ON)
DS9172-03 April 2002
JMAX
°
- T
C/W for SOT-223
JA
to
AMAX
calculated above
):
satisfy
JA
160mΩ. For
falls below
°
C/W for
RMAX
these
)