LCP-1250B4MDRH DELTA [Delta Electronics, Inc.], LCP-1250B4MDRH Datasheet
LCP-1250B4MDRH
Related parts for LCP-1250B4MDRH
LCP-1250B4MDRH Summary of contents
Page 1
... RoHS Compliant Single Mode SFP Transceiver for GbE and Fiber Channel Description The LCP-1250 series are hot pluggable 3.3V Small-Form-Factor transceiver modules designed expressly for high-speed applications that require rates up to 1.25Gb/s. The transceiver is data rate transparent, which means it can support GbE (1.25Gb/s) as well as 1x Fiber channel (1 ...
Page 2
Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage Recommended Operating Conditions Parameter Case Operating Temperature Supply Voltage Note 1: See order information Electrical Characteristics =3.3V ± 5 Parameter Total Supply Current Transmitter Transmitter Differential Input Voltage Transmitter Disable ...
Page 3
... LCP-1250B4Mxx LCP-1250D4Mxx LCP-1250D4Wxx LCP-1250D4Rxx LCP-1250D4Vxx Optical Extinction Ratio Center Wavelength LCP-1250B4 Series LCP-1250D4 Series Spectral Width LCP-1250B4Mxx (-20dB) LCP-1250D4 Series (-20dB) Side-mode Suppression Ratio LCP-1250B4Mxx LCP-1250D4 Series Optical Rise/ Fall Time Relative Intensity Noise Output Eye Receiver Sensitivity (Avg.) LCP-1250B4Mxx LCP-1250D4Mxx ...
Page 4
Mask of the eye diagram for the optical transmit signal SFP Transceiver Electrical Pad Layout DELTA ELECTRONICS, INC. 4 www.deltaww.com Aug., 2006 Rev. 6A ...
Page 5
Pin Function Definitions Pin Num. Name 1 VeeT Transmitter Ground 2 TX Fault Transmitter Fault Indication 3 TX Disable Transmitter Disable 4 MOD-DEF2 Module Definition 2 5 MOD-DEF1 Module Definition 1 6 MOD-DEF0 Module Definition 0 7 Rate Select Not ...
Page 6
The voltage swing on these lines will be between 370 and 2000 mV differential (185 – 1000 mV single ended) when properly terminated. 7) VccR and VccT are the receiver ...
Page 7
Package Outline Drawing DELTA ELECTRONICS, INC. 7 www.deltaww.com Aug., 2006 Rev. 6A ...
Page 8
SFP timing parameters for SFP management Parameter TX_DISABLE Assert time TX_DISABLE Negate time Time to initialize, including reset of TX_FAULT TX Fault Assert Time TX_DISABLE to reset LOS Assert Time LOS Deassert Time Serial ID Clock Rate Notes: Time from ...
Page 9
Enhanced Digital Diagnostic Interface The memory map in the following describes an extension to the memory map defined in SFP MSA. The enhanced interface uses the two wire serial bus address 1010001X(A2h) to provide diagnostic information about the module’s present ...
Page 10
EEPROM Serial ID Memory Contents (2-Wire Address A0h) Address Hex ASCII Note ...
Page 11
Byte 95: Check sum of bytes 64-94. 10) Byte 128 to 255 had been set hex 00. Digital Diagnostic Monitoring Interface Alarm and Warning Thresholds (2-Wire Address A2h) # Address Bytes 00-01 2 Temp High Alarm 02-03 2 Temp ...
Page 12
Byte 95 contains the low order 8bits of sum of bytes 0-94 6) State/ Control Bits Byte Bit 110 7 Tx Disable State 110 6 Soft Tx Disable 110 5 Reserved 110 4 Rate Select tate 110 3 Soft ...
Page 13
... Voltage is measured internal to the transceiver. Regulatory Compliance Test Item (#1) Electromagnetic Interference EMC (#2) Immunity： Radio Frequency Electromagnetic Field (#3) Immunity： Electrostatic Discharge to the Duplex SC Receptacle (#4) Electrostatic Discharge to the Electrical Pins Ordering information for SFP modules LCP-1250X Fiber 1 ...