LCP-155A4HDR DELTA [Delta Electronics, Inc.], LCP-155A4HDR Datasheet
LCP-155A4HDR
Related parts for LCP-155A4HDR
LCP-155A4HDR Summary of contents
Page 1
... Switch to Switch interface Switched backplane applications File server interface Performance SFP Multi-source LCP-155A4HDR Data Link up to 2km in digital diagnostic 62.5/125μm in Multi-Mode Fiber , TX CC LCP-155B4JDR Data Link up to 15km in 9/125μm Single Mode Fiber LCP-155B4MDR Data Link up to 40km in 9/125μm Single Mode Fiber 1 Nov ...
Page 2
Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage Recommended Operating Conditions Parameter Case Operating Temperature Supply Voltage Note 1: See order information Electrical Characteristics =3.3V ± 5 Parameter Total Supply Current Transmitter Transmitter Differential Input Voltage Transmitter Disable ...
Page 3
... LCP-155B4JDR LCP-155B4MDR Optical Rise/ Fall Time Output Eye Receiver Sensitivity (Avg.) LCP-155A4HDR LCP-155B4JDR LCP-155B4MDR Input Optical Wavelength LOS-Deasserted (Avg.) LCP-155A4HDR LCP-155B4JDR LCP-155B4MDR LOS-Asserted (Avg.) LOS-Hysteresis Overload LCP-155A4HDR LCP-155B4JDR LCP-155B4MDR Notes: 1. These are unfiltered 10%~90% values 2. The sensitivity is provided at a BER of 1×10 ...
Page 4
Mask of the eye diagram for the optical transmit signal SFP Transceiver Electrical Pad Layout DELTA ELECTRONICS, INC. 4 www.deltaww.com Nov., 2006 Rev. 1E ...
Page 5
Pin Function Definitions Pin Num. Name 1 VeeT Transmitter Ground 2 TX Fault Transmitter Fault Indication 3 TX Disable Transmitter Disable 4 MOD-DEF2 Module Definition 2 5 MOD-DEF1 Module Definition 1 6 MOD-DEF0 Module Definition 0 7 Rate Select Not ...
Page 6
VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP connector pin. Maximum supply current is 300mA. Recommended host board power supply filtering is shown below. Inductors with DC resistance ...
Page 7
Package Outline Drawing DELTA ELECTRONICS, INC. 7 www.deltaww.com Nov., 2006 Rev. 1E ...
Page 8
SFP timing parameters for SFP management Parameter TX_DISABLE Assert time TX_DISABLE Negate time Time to initialize, including reset of TX_FAULT TX Fault Assert Time TX_DISABLE to reset LOS Assert Time LOS Deassert Time Serial ID Clock Rate Notes: Time from ...
Page 9
Enhanced Digital Diagnostic Interface The memory map in the following describes an extension to the memory map defined in SFP MSA. The enhanced interface uses the two wire serial bus address 1010001X(A2h) to provide diagnostic information about the module’s present ...
Page 10
EEPROM Serial ID Memory Contents (2-Wire Address A0h) Address Hex ASCII Note ...
Page 11
Byte 84-91: Date code. 9) Byte 95: Check sum of bytes 64-94. 10) Byte 128 to 255 had been set hex 00. Digital Diagnostic Monitoring Interface Alarm and Warning Thresholds (2-Wire Address A2h) # Address Bytes 00-01 2 Temp ...
Page 12
P : Sensitivity optical power of receiver S 5) Byte 95 contains the low order 8bits of sum of bytes 0-94 6) State/ Control Bits Byte Bit 110 7 Tx Disable State 110 6 Soft Tx Disable 110 5 Reserved ...
Page 13
... Voltage is measured internal to the transceiver Regulatory Compliance Test Item (#1) Electromagnetic Interference EMC (#2) Immunity： Radio Frequency Electromagnetic Field (#3) Immunity： Electrostatic Discharge to the Duplex SC Receptacle (#4) Electrostatic Discharge to the Electrical Pins Ordering information for SFP modules LCP-155X Fiber 1 ...