CXOHT4SHGE RSG [RSG Electronic Components GmbH], CXOHT4SHGE Datasheet - Page 2

• Manufacturer Part Number: CXOHT4SHGE
• Description: HIGH TEMPERATURE OSCILLATORS
• Manufacturer: RSG [RSG Electronic Components GmbH]

Distribution:
RSG Electronic Components GmbH
Tel. [phone]
Änderungen vorbehalten / subject to change without notice
SPECIFICATIONS
Specifications are typical at 25
Specifications are subject to change without notice. Tighter
specifications available. Please contact factory.
Supply Voltage
Calibration Tolerance
Frequency Stability
Over Temperature
Total Tolerance
Supply Current (Typical)
Output Load (CMOS)
Start-up Time
Rise/Fall Time
Duty Cycle
Aging, first year
Aging, 1,000 Hrs
Shock, survival
Vibration, survival
Operating Temp Range -55
1. All frequencies, voltages, temperature ranges and enable/disable options may not be
available. Contact factory.
2. Total Tolerance = Calibration Tolerance + Frequency Stability over temperature.
3. For non-high-shock CXOHT and CXOMHT oscillators only. The specification for
CXOXHT oscillators is 5,000 g, 0.3 ms, 1
4. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing available.
Note: All parameters are measured at ambient temperature with a 10 M!, 15 pF load.
PACKAGING OPTIONS
CXOHT, CXOMHT, CXOXHT - Tray Pack
- 16 mm tape, 7” or 13” reels
Per EIA 481 (see Tape and Reel data sheet # 10109)
HOW TO ORDER CXOHT, CXOMHT and CXOXHT OSCILLATORS
CXOMHT
CXOMHT
CXOXHT
CXOHT
Supply Voltage
4 = 3.3 V
5 = 5.0 V
3
4
1
2
4
■
custom design.
“S” if special or
Fax [phone]
Blank if Std.
5.0 V ± 10%
± 50 ppm, or tighter as required
± 100 ppm for 25
± 150 ppm for 25
± 175 ppm for 25
± 200 ppm for 25
15 pF
100 ppm MAX at 200
HG: 10,000 g, 0.3 ms,
3.3 V ± 10%
24 MHz
32 MHz
50 MHz
120 MHz
5 ms MAX
6 ns MAX
40% MIN, 60% MAX
10 ppm MAX at 25
Std: 3,000 g, 0.3 ms,
20 g, 10-2,000 Hz swept sine
S
O
C up to 200
/
HG = High Shock
O
2 sine.
otherwise leave
C unless otherwise noted.
■
blank.
Sprendlinger Landstr. 115
3.3 V
3.0 mA
5.0 mA
6.0 mA
23.0 mA
Enable/Disable
Option E or T
O
O
O
O
C to 200
or N
C
C to 150
C to 175
■
O
O
C to 200
[e-mail]
C
E
O
C
1
/
1
2
/
2
5.0 V
8.0 mA
10.0 mA
14.0 mA
39.0 mA
sine
O
Terminations
Blank = SM1
SM3 = Solder Dipped
SM5 = Solder Dipped
O
O
sine
C
C
C
O
C
= Gold Plated
(Lead Free)
SM3
■
D-63069 Offenbach/Germany
■
www.rsg-electronic.de
Calibration
Tolerance
(in ppm)
@ 25
*
ABSOLUTE MAXIMUM RATINGS
Supply Voltage V
Storage Temperature
Maximum Process Temperature
ENABLE/DISABLE OPTIONS (E/T/N)
Statek offers three enable/disable options: E, T, and N.
Both the E-version and T-version have Tri-State outputs
and differ in whether the oscillator continues to run
internally when the output is put into the high Z state: it
stops in the E-version and continues to run in the T-version.
So, the E-version offers very low current consumption
when the oscillator is disabled and the T-version offers very
fast output recovery when the oscillator is re-enabled. The
N-version does not have PIN 1 connected internally and so
has no enable/disable capability. The following table
summarizes the three options.
When enabled (PIN 1 is high*)
When disabled (PIN 1 is low)
When re-enabled (PIN 1 changes from low to high)
ENABLE/DISABLE OPTIONS E AND T
When PIN 1 is allowed to float, it is held high by an internal pull-up resistor.
25
Frequency
M = MHz
20.0M,
K = kHz
Output
Oscillator
Current consumption
Output
Oscillator
Current consumption
Output recovery
0
C
OR
/
Temp. Range
Stability over
Frequency
(in ppm)
175
Calibration
Tolerance
@ 25
(in ppm)
COMPARISON OF
DD
0
C
/
Frequency
Tolerance
(in ppm)
/
Total
Temp. Range
Stability over
Frequency
(in ppm)
Freq. output
Oscillates
Normal
High Z state
Stops
Very low
Delayed
/
Total Frequency
Specified Temp.
E
Temp. Range:
S = Customer
Tolerance (in
H = 25
/ 200
H
200
Range
ppm)
-0.3 V to 7.0 V
-55
260
0
0
C
C to
O
O
C to 125
C, 20 seconds
Freq. output
Oscillates
Normal
High Z state
Oscillates
Lower than normal
Immediate
/
H = 25
Specified Temp.
S = Customer
Temp. Range:
O
C
Range
T
0
C to 200
H
0
C