PE42540 PEREGRINE [Peregrine Semiconductor Corp.], PE42540 Datasheet
PE42540
Available stocks
Related parts for PE42540
PE42540 Summary of contents
Page 1
... Product Description The PE42540 is a HaRP™ technology-enhanced absorptive SP4T RF switch developed on UltraCMOS process technology. This switch is designed specifically to support the requirements of the test equipment and ATE market comprised of four symmetric RF ports and has very high isolation. An on-chip CMOS decode logic facilitates a two-pin low voltage CMOS control interface and an optional external Vss feature ...
Page 2
... Document No. 70-0299-08 | UltraCMOS PE42540 Product Specification Max Unit 8 GHz 1.0 dB 1.1 dB 1.3 dB 1 μs 45 μ ...
Page 3
... PE42540 Product Specification Figure 3. Pin Configuration (Top View) Table 2. Pin Descriptions Pin # Pin Name 1, 3-6, 8, 9-12, 14-17, GND Ground 19-22, 24-26, 28 RF4 RF I RF2 RF I RFC RF Common 2 18 RF1 RF I RF3 RF I Supply Switch control input, CMOS logic level 30 V2 Switch control input, CMOS logic level ...
Page 4
... State RF1 on RF2 on RF3 on RF4 on ® Moisture Sensitivity Level The Moisture Sensitivity Level rating for the PE42540 in the 32-lead 5x5 mm LGA package is MSL3. EXT control pin must EXT control pin is EXT can be applied externally to bypass the EXT = 0V (pin 31 = GND). If ...
Page 5
... PE42540 Product Specification Low Frequency Operation Table 6 shows the minimum and maximum voltage limits when operating the device under various V and Vss voltage conditions below DD EXT 9 kHz. Refer to Figures 4, 5, and 6 to determine the maximum operating power over the frequency range of the device. ...
Page 6
... VssEXT = -3 .0V , VDD = +3.0 V VssEXT = 0.0V, VDD ≥ +3.0V VssEXT= -3.5V, VDD=+3.5V 1,000 10,000 100 ,00 0 1,000,000 = 85 ambient VssEXT = -3 .0V , VDD = +3.0 V VssEXT = 0.0V, VDD ≥ +3.0V VssEXT= -3.5V, VDD=+3.5V 1,000 10,000 100 ,00 0 1,000,000 Document No. 70-0299-08 Product Specification ® | UltraCMOS RFIC Solutions PE42540 ...
Page 7
... PE42540 Product Specification Figure 7. Insertion Loss vs. V (Temp = 25°C, Vss = 0) Frequency (Hz) Figure 9. Insertion Loss (Temp = 25° 3.3V, Vss = 0) DD Frequency (Hz) Figure 11. Isolation: RFX-RFX vs. Temp (V = 3.3V, Vss = 0) DD Frequency (Hz) Document No. 70-0299-08 | www.psemi.com Figure 8. Insertion Loss vs. Temp DD Figure 10. Isolation: RFX-RFX vs. V Figure 12. Isolation: RFX-RFC vs ...
Page 8
... Page Figure 14. Active Port Return Loss vs. V (Temp = 25°C, Vss = 0) Frequency (Hz) Figure 16. Terminated Port Return Loss vs. V (Temp = 25°C, Vss = 0) Frequency (Hz) Figure 18. RFC Port Return Loss vs. V (Temp = 25°C, Vss = 0) Frequency (Hz) Document No. 70-0299-08 | UltraCMOS PE42540 Product Specification ® RFIC Solutions ...
Page 9
... PE42540 Product Specification Figure 19. RFC Port Return Loss vs. Temp (V = 3.3V, Vss = 0) DD Frequency (Hz) Figure 20. Linearity Performance (Temp = 25° 120 100 10.0E+3 100.0E+3 Document No. 70-0299-08 | www.psemi.com = 3.3V, Vss = 0) 1.0E+6 10.0E+6 Frequency (Hz) Frequency [Hz] Nominal IIP3 [dBm] Nominal IIP2 [dBm] 100.0E+6 1.0E+9 ©2010-2012 Peregrine Semiconductor Corp. All rights reserved. ...
Page 10
... Evaluation Kit The SP4T switch EK Board was designed to ease customer evaluation of Peregrine’s PE42540. The RF common port is connected through a 50Ω transmission line via the top SMA connector, J1. RF1, RF2, RF3 and RF4 are connected through 50Ω transmission lines via SMA connectors J2, J4, J3 and J5, respectively. A through 50Ω ...
Page 11
... PE42540 Product Specification Figure 23. Package Drawing 5. 5.00 0.10 C (2X) Pin #1 Corner TOP VIEW 0.10 C 0.70 0.05 C SEATING PLANE SIDE VIEW 0.10 0.535 0.04 0.11 0.10 DETAIL A Figure 24. Marking Specifications 42540 YYWW ZZZZZZ Document No. 70-0299-08 | www.psemi.com 0.10 C (2X) 3.03±0.05 DETAIL A 17 0.50 (x28) 16 3.50 0.34 (x32) 0.26±0.05 9 (x32) 8 3.50 BOTTOM VIEW 1.01 MAX 0. 0.05 C ALL FEATURES ...
Page 12
... Tape Feed Direction Ao = 5.25 ± 0. 5.25 ± 0. 1.1 ± 0.05 mm Description PE42540 SP4T RF switch Green 32-lead 5x5 mm LGA PE42540 Evaluation kit No patent rights or licenses to any circuits described in this datasheet are implied or granted to any third party. Peregrine’s products are not designed or intended for use in devices or systems intended for surgical implant other applications intended to support or sustain life any application in which the failure of the Peregrine product could create a situation in which personal injury or death might occur ...