MAX148BEPP Maxim Integrated, MAX148BEPP Datasheet - Page 2

• Manufacturer Part Number: MAX148BEPP
• Description: Analog to Digital Converters - ADC
• Manufacturer: Maxim Integrated

Specifications of MAX148BEPP

• Number Of Channels: 8/4
• Architecture: SAR
• Conversion Rate: 133 KSPs
• Resolution: 10 bit
• Input Type: Single-Ended/Differential
• Snr: Yes
• Interface Type: 4-Wire, Microwire, QSPI, Serial, SPI
• Operating Supply Voltage: 2.7 V to 5.25 V
• Maximum Operating Temperature: + 85 C
• Package / Case: PDIP N
• Maximum Power Dissipation: 640 mW
• Minimum Operating Temperature: - 40 C
• Number Of Converters: 1
• Voltage Reference: External

+2.7V to +5.25V, Low-Power, 8-Channel,
Serial 10-Bit ADCs
ABSOLUTE MAXIMUM RATINGS
V
AGND to DGND ...................................................-0.3V to +0.3V
CH0–CH7, COM to AGND, DGND ........... -0.3V to (V
V
Digital Inputs to DGND ...........................................-0.3V to +6V
Digital Outputs to DGND .......................... -0.3V to (V
Digital Output Sink Current ................................................25mA
Continuous Power Dissipation (T
ELECTRICAL CHARACTERISTICS
(V
MAX149—4.7FF capacitor at V
otherwise noted.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may
affect device reliability.
2
DC ACCURACY (Note 1)
Resolution
Relative Accuracy (Note 2)
Differential Nonlinearity
Offset Error
Gain Error (Note 3)
Gain Temperature Coefficient
Channel-to-Channel Offset
Matching
DYNAMIC SPECIFICATIONS (10kHz Sine-Wave Input, 0 to 2.500V
Signal-to-Noise + Distortion
Noise
Total Harmonic Distortion
Spurious-Free Dynamic Range
Channel-to-Channel Crosstalk
Small-Signal Bandwidth
Full-Power Bandwidth
CONVERSION RATE
Conversion Time (Note 5)
Track/Hold Acquisition Time
Aperture Delay
Aperture Jitter
DD
REF
PDIP (derate 11.11mW/NC above +70NC) ...................889mW
SSOP (derate 8.00mW/NC above +70NC) ....................640mW
DD
to AGND, DGND ..............................................-0.3V to +6V
, REFADJ to AGND ...........................-0.3V to (V
= +2.7V to +5.25V; COM = 0; f
PARAMETER
REF
A
= +70NC)
pin; MAX148—external reference, V
SYMBOL
SINAD
t
SFDR
CONV
t
SCLK
DNL
THD
ACQ
INL
= 2.0MHz; external clock (50% duty cycle); 15 clocks/conversion cycle (133ksps);
MAX14_A
MAX14_B
No missing codes over temperature
MAX14_A
MAX14_B
MAX14_A
MAX14_B
Up to the 5th harmonic
65kHz, 2.500V
-3dB rolloff
Internal clock, SHDN = unconnected
Internal clock, SHDN = V
External clock = 2MHz, 12 clocks/
conversion
DD
DD
DD
+ 0.3V)
+ 0.3V)
+ 0.3V)
P-P
CONDITIONS
(Note 4)
Operating Temperature Ranges
Storage Temperature Range ............................ -60NC to +150NC
Lead Temperature (soldering, 10s) ................................+300NC
Soldering Temperature (reflow) ......................................+260NC
P-P
MAX148_C_P/MAX149_C_P .............................. 0NC to +70NC
MAX148_E_P/MAX149_E_P ............................ -40NC to +85NC
MAX149BMAP ............................................... -55NC to +125NC
REF
, 133ksps, 2.0MHz External Clock, Bipolar Input Mode)
DD
= 2.500V applied to V
MIN
REF
5.5
10
35
6
pin; T
±0.15
±0.15
±0.25
±0.05
TYP
2.25
< 50
-70
-75
1.0
66
70
30
A
= T
MIN
MAX
±0.5
±1.0
7.5
1.5
±1
±1
±2
±1
±2
65
to T
MAX
ppm/°C
UNITS
, unless
MHz
MHz
LSB
LSB
LSB
LSB
LSB
Bits
dB
dB
dB
dB
μs
μs
ns
ps