SLFDM44V-1GM1UI STEC, SLFDM44V-1GM1UI Datasheet

Page 1

... ORDERING INFORMATION SimpleTech Part No. Connector SLFDM40LPV-xxxJ(I) .................. 40-Pin ....................... Vertical SLFDM40LPH-xxxJ(I) ................. 40-Pin ................. Horizontal SLFDM44V-xxxJ(I) ....................... 44-Pin ....................... Vertical SLFDM44H-xxxJ(I) ...................... 44-Pin ................. Horizontal where xxx = 128, 256, 512 for capacity in MB, 1GB, 2GB for capacity in GB and A part number without the “I” suffix selects commercial operating temperature range. A part number with the “ ...

Page 2

SLFDM(40/44)(LP)(V/H)-xxxJ(I) DIMENSIONS AND JUMPERS Units are in inches. Tolerances are ±0.005. SLFDM40LPV-xxxJ(I) Location of Pin 1 (Top View of Connector) 0.125 0.140 SLFDM40LPH-xxxJ(I) Location of Pin 1 0.125 0.125 FLASH DISK MODULE 40-Pin IDE Connector 0.380±0.050 2.135 VCC GND 4-Pin ...

Page 3

... SLFDM(40/44)(LP)(V/H)-xxxJ(I) DIMENSIONS AND JUMPERS Units are in inches. Tolerances are ±0.005. SLFDM44V-xxxJ(I) Location of Pin 1 (Top View of Connector) 0.175 0.105 SLFDM44H-xxxJ(I) Location of Pin 1 0.175 0.075 FLASH DISK MODULE (continued) 44-Pin IDE Connector 0.072 D 2.000 0.125 D 2plcs 1.900 0.100 1.265 0.240 0.080 44-Pin IDE Connector 0 ...

Page 4

SLFDM(40/44)(LP)(V/H)-xxxJ(I) PIN CONFIGURATION Pinout Pin Pin Pin Num Symbol Num Symbol 1 -RESET 23 2 GND 24 3 D07 25 4 D08 26 5 D06 27 6 D09 28 7 D05 29 8 D10 30 9 D04 31 10 D11 ...

Page 5

SLFDM(40/44)(LP)(V/H)-xxxJ(I) Signal Description Signal Name Dir -DASP I/O D15-D00 I/O 18, 16, 14, 12, 10 11, 13, 15, 17 -IOWR I -IORD I INTRQ O A2-A0 I 35, 33, 36 -CS1, -CS2 I ...

Page 6

SLFDM(40/44)(LP)(V/H)-xxxJ(I) ABSOLUTE MAXIMUM RATINGS Parameter Voltage on any pin w.r.t. Vss Storage Temperature range RECOMMENDED OPERATING CONDITIONS Parameter Commercial operating temperature Industrial operating temperature VCC voltage PERFORMANCE Item Data Transfer Rate To/From Host Sustained Read Sustained Write RELIABILITY Item Data ...

Page 7

SLFDM(40/44)(LP)(V/H)-xxxJ(I) DC CHARACTERISTICS temperature parts; VCC=5V±5%) Symbol Parameter VIL Input LOW Voltage VIH Input HIGH Voltage VOL Output LOW Voltage VOH Output HIGH Voltage ICC Operating Current, VCC=5.0V Sleep mode Operating ILI Input Leakage Current ILO Output Leakage Current CI/O ...

Page 8

SLFDM(40/44)(LP)(V/H)-xxxJ(I) AC CHARACTERISTICS temperature parts; VCC=5V±5%) Register Access AC Characteristics for True IDE Parameter Cycle time (min) Address valid to -IORD/-IOWR (min) setup -IORD/-IOWR pulse width 8bit (min) -IORD/-IOWR recovery time (min) -IOWR data setup (min) -IOWR data hold (min) ...

Page 9

SLFDM(40/44)(LP)(V/H)-xxxJ(I) AC CHARACTERISTICS True IDE Mode Access Read/Write Timings ADDR valid -IORD/-IOWR D15 to D0 (Write) D15 to D0 (Read) -IOIS16 IORDY FLASH DISK MODULE (continued Document Part Number 61000-02832-113 March 2005 t8 t9 ...

Page 10

SLFDM(40/44)(LP)(V/H)-xxxJ(I) TRUE IDE MODE The drive is configured in a True IDE mode at power up. The data register is accessed in word (16-bit) mode at power up. The drive permits 8-bit accesses if the host issues a Set Feature ...

Page 11

SLFDM(40/44)(LP)(V/H)-xxxJ(I) TASK FILE REGISTER SPECIFICATION These registers are used for reading and writing data to the drive. True IDE Mode I/O Map -CE2 -CE1 ...

Page 12

SLFDM(40/44)(LP)(V/H)-xxxJ(I) Data Register The Data Register bit read/write register used for transferring data between the drive and the host. This register can be accessed in word mode and byte mode. bit15 bit14 bit13 bit12 bit11 bit10 Error ...

Page 13

SLFDM(40/44)(LP)(V/H)-xxxJ(I) Sector Count Register This register contains the numbers of sectors of data requested to be transferred on a read or write operation between the host and the drive. If the value in the register count of ...

Page 14

SLFDM(40/44)(LP)(V/H)-xxxJ(I) Drive/Head Register This register select the device address translation (CHS or LBA) and provides head address (CHS) or high order address bits 27:24 for LBA. bit7 bit6 bit5 bit4 1 LBA 1 DRV bit Name LBA ...

Page 15

SLFDM(40/44)(LP)(V/H)-xxxJ(I) Status Register This read only register indicates status of a command execution. When the BSY bit is “0”, the other bits are valid; when the BSY bit is “1”, the other bits are not valid. When the register is ...

Page 16

... When set to “0”, it enables interrupts to the host (using the -IREQ tri-state pin). When inactive (set to “1”) or drive is not selected, it disables all pending interrupts (-IREQ in high-Z). This bit is ignored in memory mode. This bit is set to “0”. bit3 ...

Page 17

SLFDM(40/44)(LP)(V/H)-xxxJ(I) ATA COMMAND SPECIFICATIONS This table with the following paragraphs summarizes the ATA command set. No. Command set 1 Check Power Mode 2 Execute Drive Diagnostic 3 Erase Sector(s) 4 Format Track 5 Identify Drive 6 Idle 7 Idle Immediate ...

Page 18

SLFDM(40/44)(LP)(V/H)-xxxJ(I) Check Power Mode (code: E5h or 98h) This command checks the power mode. Execute Drive Diagnostic (code: 90h) This command performs the internal diagnostic tests implemented by the drive. See ERROR register for dianostic codes. Erase Sector(s) (code: C0h) ...

Page 19

SLFDM(40/44)(LP)(V/H)-xxxJ(I) Identify Drive Information (continued) (Serial Number, Firmware Revision, and Model Number) Serial Number Format (typical): Words 10-19 SimpleTech Proprietary Yr Day STI_J13C0 04 224 Firmware Revision: Words 23-26 mm/dd/yy Model Number: Words 27-46 STI Flash X.Y.Z Idle (code: E3h ...

Page 20

SLFDM(40/44)(LP)(V/H)-xxxJ(I) Seek (code: 7Xh) This command is effectively a NOP command to the drive although it does perform a range check. Set Features (code: EFh) This command is used by the host to establish or select certain features. Feature 01H ...

Page 21

SLFDM(40/44)(LP)(V/H)-xxxJ(I) Write Sector(s) (code: 30h or 31h) This command writes from 1 to 256 sectors as specified in the Sector Count register. A sector count of zero requests 256 sectors. The transfer begins at the sector specified in the Sector ...

Page 22

SLFDM(40/44)(LP)(V/H)-xxxJ(I) REVISION HISTORY Rev. Change Description from Previous Revision -101 3/1/04. Initial Release. -102 5/26/04. General Description updated with new marketing copy. R/W speeds changed from 5.4/4.5MB/s to 5/5MB/s. 32MB, 64MB, 3GB, and 4GB versions removed. CHS Parameter table added. ...