SLFLD25-3GBJ STEC, SLFLD25-3GBJ Datasheet - Page 17

• Manufacturer Part Number: SLFLD25-3GBJ
• Description: Solid State Drives - SSD 3GB 2.5-Inch
• Manufacturer: STEC

Specifications of SLFLD25-3GBJ

• Product Category: Solid State Drives - SSD
• Product: IDE Flash Drives
• Memory Size: 3 GB
• Sustained Read: 5 MB/s
• Sustained Write: 5 MB/s
• Active Mode Current: 30 mA
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 70 C
• Connector Type: 44-pin IDE
• Dimensions: 100.2 mm x 69.85 mm x 4 mm
• Minimum Operating Temperature: 0 C

SLFLD25-xxxJ(I)
Check Power Mode
(code: E5h or 98h)
This command checks the power mode.
Execute Drive Diagnostic
(code: 90h)
This command performs the internal diagnostic tests
implemented by the drive. See ERROR register for dianostic
codes.
Erase Sector(s)
(code: C0h)
This command is used to pre-erase and condition data
sectors in advance.
XXXXH: These values are dependent upon the the specific card.
Address
69-255
Word
10-19
23-46
60-61
7-8
2 0
2 1
2 2
4 7
4 8
4 9
5 0
5 1
5 2
5 3
5 4
5 5
5 6
5 7
5 8
5 9
6 2
6 3
6 4
6 5
6 6
6 7
6 8
0
1
2
3
4
5
6
9
044AH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
00XXH
010XH
0000H
0000H
0004H
0001H
0000H
0200H
0000H
0200H
0000H
0000H
0000H
0003H
0000H
0000H
0078H
0078H
0000H
0003h
Data
Bytes
Total
388
2 0
4 8
2
2
2
2
2
2
2
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
4
2
2
2
2
2
2
2
General configuration bit-significant information—value fixed by CFA
Default number of cylinders
Reserved
Default number of heads
Do not use this word. Before retirement, was number of unformatted bytes per track
Do not use this word. Before retirement, was number of unformatted bytes per sector
Default number of sectors per track
Number of sectors per card (word7=MSW, word 8 = LSW)
Reserved
Serial Number (see table next page for definition)
Do not use this word. Before retirement, was buffer type
Do not use this word. Before retirement, was buffer size in 512 byte increments
# of ECC bytes passed on Read/Write Long commands
Firmware revision and model number in ASCII (see table next page for definition)
Maximum of 1 sector on Read/Write Multiple command
Double Word not supported
DMA not supported, LBA supported
Reserved
PIO data transfer cycle timing mode
Single word DMA data transfer cycle timing mode (not supported)
Words 54 - 58 and 64 - 70 are valid
Number of Current Cylinders
Number of Current Heads
Number of Current Sectors Per Track
LSW of the Current Capacity in Sectors
MSW of the Current Capacity in Sectors
Current Setting for Block Count=1 for R/W Multiple commands
Total number of sectors addressable in LBA Mode
Single word DMA transfer not supported
Multiword DMA modes not supported
Advanced PIO modes supported (modes 3 and 4)
Minimum multiword DMA transfer cycle time per word (ns)
Recommended multiword DMA transfer cycle time per word (ns)
Minimum PIO transfer without flow control
Minimum PIO transfer with IORDY flow control
Reserved
Identify Drive Information (Typical)
Document Part Number 61000-02817-109 March 2005
Format Track
(code: 50h)
This command writes the desired head and cylinder of the
selected drive with a vender unique data pattern (typically
00h or FFh). This drive accepts a sector buffer of data from
the host to follow the command with the same protocol as
the Write Sector Command although the information in the
buffer is not used.
Identify Drive
(code: ECh)
This command enables the host to receive parameter
information from the drive. (See table below.)
Description
IDE FLASH DRIVE
Page 17