AT24C16BN-SH-B Atmel, AT24C16BN-SH-B Datasheet
AT24C16BN-SH-B
Specifications of AT24C16BN-SH-B
Available stocks
Related parts for AT24C16BN-SH-B
AT24C16BN-SH-B Summary of contents
Page 1
... Description The AT24C16B provides 16384 bits of serial electrically erasable and programmable read-only memory (EEPROM) organized as 2048 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The AT24C16B is available in space-saving ...
Page 2
Absolute Maximum Ratings Operating Temperature..................................–55°C to +125°C Storage Temperature .....................................–65°C to +150°C Voltage on Any Pin with Respect to Ground .................................... –1.0V to +7.0V Maximum Operating Voltage .......................................... 6.25V DC Output Current........................................................ 5.0 mA Figure 2-1. Block Diagram VCC GND ...
Page 3
... Table 3-1. WP Pin Status GND 4. Memory Organization AT24C16B, 16K SERIAL EEPROM: Internally organized with 128 pages of 16 bytes each, the 16K requires an 11-bit data word address for random word addressing. 5175E–SEEPR–3/09 Table 3-1. Write Protect Part of the Array Protected ...
Page 4
Table 4-1. Pin Capacitance Applicable over recommended operating range from T Symbol Test Condition C Input/Output Capacitance (SDA) I/O C Input Capacitance (SCL) IN Note: 1. This parameter is characterized and is not 100% tested. Table 4-2. DC Characteristics ...
Page 5
Table 4-3. AC Characteristics (Industrial Temperature) Applicable over recommended operating range from T erwise noted). Test conditions are listed in Note 2. Symbol Parameter f Clock Frequency, SCL SCL t Clock Pulse Width Low LOW t Clock Pulse Width High ...
Page 6
Device Operation CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods (see page 8). Data changes during SCL high periods ...
Page 7
Bus Timing Figure 6-1. SCL: Serial Clock, SDA: Serial Data I/O SCL t SU.STA SDA IN SDA OUT 7. Write Cycle Timing Figure 7-1. SCL: Serial Clock, SDA: Serial Data I/O SCL SDA 8th BIT WORDn Note: 1. The ...
Page 8
Figure 7-2. Data Validity SDA SCL Figure 7-3. Start and Stop Definition SDA SCL Figure 7-4. Output Acknowledge SCL DATA IN DATA OUT AT24C16B 8 DATA STABLE DATA STABLE DATA CHANGE START 1 START STOP 8 9 ACKNOWLEDGE 5175E–SEEPR–3/09 ...
Page 9
... The device address word consists of a mandatory one, zero sequence for the first four most sig- nificant bits as shown. This is common to all the EEPROM devices. The next 3 bits used for memory page addressing and are the most significant bits of the data word address which follows. ...
Page 10
... The address “roll over” during read is from the last byte of the last memory page to the first byte of the first page. The address “roll over” during write is from the last byte of the current page to the first byte of the same page ...
Page 11
Figure 10-2. Byte Write Figure 10-3. Page Write Figure 10-4. Current Address Read 5175E–SEEPR–3/09 11 ...
Page 12
Figure 10-5. Random Read Figure 10-6. Sequential Read AT24C16B 12 5175E–SEEPR–3/09 ...
Page 13
... AT24C16B Ordering Information Ordering Codes AT24C16B-PU (Bulk Form Only) AT24C16BN-SH-B (1) (NiPdAu Lead Finish) (2) AT24C16BN-SH-T (NiPdAu Lead Finish) (1) AT24C16B-TH-B (NiPdAu Lead Finish) AT24C16B-TH-T (2) (NiPdAu Lead Finish) (2) AT24C16BY6-YH-T (NiPdAu Lead Finish) (2) AT24C16BD3-DH-T (NiPdAu Lead Finish) AT24C16BTSU-T (2) AT24C16BU3-UU-T (2) AT24C16B-W-11 (3) Notes: 1. “-B” denotes bulk. ...
Page 14
Part Marking 11.1 8-PDIP TOP MARK |---|---|---|---|---|---|---|---| A |---|---|---|---|---|---|---|---| 1 |---|---|---|---|---|---|---|---| * |---|---|---|---|---|---|---|---| | Pin 1 Indicator (Dot SEAL YEAR 6: 2006 7: 2007 8: 2008 9: 2009 Lot Number to Use ALL Characters in Marking BOTTOM ...
Page 15
TOP MARK |---|---|---|---|---|---|---|---| A |---|---|---|---|---|---|---|---| 1 |---|---|---|---|---|---|---|---| * |---|---|---|---|---|---|---|---| | Pin 1 Indicator (Dot SEAL YEAR 6: 2006 7: 2007 8: 2008 9: 2009 Lot Number to Use ALL Characters in Marking BOTTOM MARK 5175E–SEEPR–3/09 Seal ...
Page 16
TOP MARK BOTTOM MARK |---|---|---|---|---|---|---| |---|---|---|---|---|---|---| |---|---|---|---|---|---|---| Y = SEAL YEAR 6: 2006 7: 2007 8: 2008 9: 2009 AT24C16B 16 Pin 1 Indicator (Dot) | |---|---|---|---| * |---|---|---|---|---| |---|---|---|---|---| ...
Page 17
... XX = ATMEL LOT NUMBER TO COORESPOND WITH NSEB TRACE CODE LOG BOOK. (e. AA, AB, AC,...AX, AY, AZ SEAL YEAR 6: 2006 7: 2007 8: 2008 9: 2009 11.5 8-ULA TOP MARK Y = BUILD YEAR 2006 2007 XX = ATMEL LOT NUMBER TO COORESPOND WITH (e. AA, AB, AC,...AX, AY, AZ) 5175E–SEEPR–3/09 |---|---|---| |---|---|---| H 1 |---|---|---| |---|---|---| ...
Page 18
... M = SEAL MONTH (USE ALPHA DESIGNATOR A- JANUARY B = FEBRUARY " " """"""" OCTOBER K = NOVEMBER L = DECEMBER TC = TRACE CODE (ATMEL LOT NUMBERS TO CORRESPOND WITH ATK TRACE CODE LOG BOOK) 11.7 SOT23 TOP MARK |---|---|---|---|---| Line 1 -----------> |---|---|---|---|---| ...
Page 19
Packaging Information 12.1 8P3 – PDIP Top View PLCS Side View Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information. 2. Dimensions A and L ...
Page 20
JEDEC SOIC Top View e Side View Note: These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 ...
Page 21
TSSOP Pin 1 indicator this corner N Top View Side View Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, ...
Page 22
Mini Map D Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-229, for proper dimensions, tolerances, datums, etc. 2. Dimension b applies to metallized terminal and is measured between 0.15 mm and ...
Page 23
SOT23 E1 1 Seating Plane NOTES: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-193, Variation AB, for additional information. 2. Dimension D does not include mold flash, protrusions, or gate burrs. Mold ...
Page 24
PIN 1 BALL PAD CORNER Top View PIN 1 BALL PAD CORNER 1 2 (d1 (e1) Bottom View 8 SOLDER BALLS 1. Dimension “b” is measured at the maximum solder ball diameter. ...
Page 25
ULA PIN # TOP VIEW 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 R 5175E–SEEPR–3/ SIDE VIEW SYMBOL ...
Page 26
Revision History Lit No. 5175E 5175D 5175C 5175B 5175A AT24C16B 26 Date Comment 3/2009 Changed the Vcc to 5.5V in the test condition for Isb1 6/2008 Deleted A0, A1, A2 pin-outs AT24C16B product with date code 742 or later ...
Page 27
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...