MAX3248EEAI+ Maxim Integrated, MAX3248EEAI+ Datasheet - Page 11

• Manufacturer Part Number: MAX3248EEAI+
• Description: RS-232 Interface IC
• Manufacturer: Maxim Integrated
• Series: MAX3238E, MAX3248Er

Figure 3. Using Power-Fail Input to Monitor an Additional
Power-Supply a) V
providing an early power-fail warning so software can
conduct an orderly system shutdown. It can also be
used to monitor supplies other than V
setting the power-fail threshold with a resistor-divider, as
shown in Figure 3. PFI is the input to the power-fail com-
parator. The typical comparator delay is 2µs from PFI to
PFO. Connect PFI to ground of V
The MAX6715–MAX6729 are guaranteed to operate
properly down to V
require valid reset levels down to V
down resistor at RST to ground. The resistor value used
is not critical, but it must be large enough not to load
the reset output when V
For most applications, 100kΩ is adequate. This config-
uration does not work for the open-drain outputs of the
MAX6715/MAX6717/MAX6719/MAX6721/MAX6723/
MAX6725/MAX6727/MAX6728. For push-pull, active-
high RST output connect the external resistor as a
pullup from RST to V
V
V
V
CC
IN
IN
A
B
R1
R2
R1
R2
PFI
PFI
MAX6728/
MAX6728/
MAX6729
MAX6729
GND
GND
IN
Ensuring a Valid Reset Output
______________________________________________________________________________________
is Positive b) V
Dual/Triple Ultra-Low-Voltage SOT23 µP
CC
CC
PFO
PFO
1.
CC
= 0.8V. In applications that
is above the reset threshold.
V
V
IN
PFI
TRIP
CC
V
is Negative
= 626.5mV
TRIP
Down to V
= R2 (V
1 if unused.
CC
= V
[
PFI
CC
PFI
= 0 use a pull-
(
)
R1 + R2
1 or V
(
R2
R1
1
+
)
R2
1
CC
CC
)
-
2 by
V
R1
= 0
CC
]
Most microprocessors with bidirectional reset pins can
interface directly to open-drain RST output options.
Systems simultaneously requiring a push-pull RST out-
put and a bidirectional reset interface can be in logic
contention. To prevent contention, connect a 4.7kΩ
resistor between RST and the µP’s reset I/O port as
shown in Figure 4.
The power-fail comparator has a typical input hysteresis
of 3mV. This is sufficient for most applications where a
power-supply line is being monitored through an external
voltage-divider (see the Power-Fail Comparator section).
If additional noise margin is desired, connect a resistor
between PFO and PFI as shown in Figure 5. Select the
values of R1, R2, and R3 so PFI sees V
V
rises to its power-good trip point (V
window extends between the specified V
thresholds. R3 adds the additional hysteresis by sinking
current from the R1/R2 divider network when PFO is logic
low and sourcing current into the network when PFO is
logic high. R3 is typically an order of magnitude greater
than R1 or R2.
The current through R2 should be at least 2.5µA to
ensure that the 25nA (max) PFI input current does not
significantly shift the trip points. Therefore, R2 <
V
additional hysteresis for PFO push-pull (V
open-drain (V
Figure 4. Interfacing to µPs with Bidirectional Reset I/O
V
EXT
PFI
CC
1 V
/2.5µA < 248kΩ for most applications. R3 will provide
falls to its power-fail trip point (V
Supervisory Circuits
CC
2
Interfacing to µPs with Bidirectional
Adding Hysteresis to the Power-Fail
V
V
CC
CC
2
1
OH
MAX6715–
MAX6729
GND
Applications Information
= V
PULLUP
RST
RESET TO OTHER SYSTEM COMPONENTS
) applications.
4.7kΩ
GOOD
FAIL
PFI
RESET
FAIL
). The hysteresis
Comparator
) and when VIN
OH
(626mV) when
Reset Pins
GND
and V
µP
= V
CC
GOOD
1) or
11