MAX8934GETI+CAK Maxim Integrated, MAX8934GETI+CAK Datasheet - Page 2

• Manufacturer Part Number: MAX8934GETI+CAK
• Description: Battery Management Dual Input Linear Chargers Smart Power Selector
• Manufacturer: Maxim Integrated
• Series: MAX8934Gr

Specifications of MAX8934GETI+CAK

• Battery Type: Li-Ion, Li-Poly
• Output Voltage: 1 V
• Operating Supply Voltage: 4.1 V to 6.6 V
• Charge Safety Timers: Yes
• Operating Supply Current: 1 mA
• Product Type: Charge Management
• Temperature Monitoring: Yes

MAX8934G
Dual-Input Linear Charger, Smart Power Selector
with Advanced Battery Temperature Monitoring
DC, PEN1 to GND .................................................-0.3V to +16V
USB to GND ............................................................-0.3V to +9V
V
LDO to GND ......... -0.3V to the lower of +4V and (V
THMEN, THMSW to GND ..................... -0.3V to +(V
THM to GND .......................................-0.3V to (V
PSET, ISET, CT to GND ............................... -0.3V to (V
BATT, SYS, CEN, CHG, OT, DOK,
EP (Exposed Pad) to GND ...................................-0.3V to +0.3V
DC Continuous Current (total in two pins) .................... 2.4A
SYS Continuous Current (total in two pins) ................... 2.4A
USB Continuous Current (total in two pins) .................. 2.0A
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(V
UOK, FLT are unconnected, C
2
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
DC-to-SYS PREREGULATOR
DC Operating Voltage Range
DC Withstand Voltage
DC Undervoltage Threshold
DC Overvoltage Threshold
DC Operating Supply Current
DC Suspend Current
DC-to-SYS On-Resistance
DC to BATT Dropout Voltage
DC Current Limit
PSET Resistance Range
SYS Regulation Voltage
Input Current Soft-Start Time
Thermal-Limit Temperature
Thermal-Limit Gain
V
L
DC
UOK, FLT, DONE, USUS, PEN2 to GND .............-0.3V to +6V
L
to GND ...............................................................-0.3V to +4V
Voltage
= V
PEN1
PARAMETER
= V
PEN2
= 5V, CEN = USUS = THMEN = GND, V
CT
= 0.068FF, T
V
When V
When V
I
I
V
I
When SYS regulation and charging stops, V
150mV hysteresis
V
T
V
Connecting DC with USB not present
Connecting DC with USB present
Die temperature at when the charging current and input
current limits are reduced
I
I
SYS
SYS
SYS
SYS
VL
A
BATT
DC
DC
DC
= +25NC
= 0 to 5mA, USB = unconnected
= I
= I
= V
= 400mA, V
= 5V, V
= 6V, I
reduction with die temperature (above +100NC)
= V
BATT
BATT
DOK
DOK
CEN
A
SYS
= -40NC to +85NC, unless otherwise noted. Typical values are at T
SYS
THMSW
SYS
goes low, V
goes high, V
= 0mA, V
= 0mA, V
= V
LDO
= 0V
SYS
= 1mA to 1.75A, V
= 4V,
USUS
CEN
L
+ 0.3V)
+ 0.3V)
+ 0.3V)
+ 0.3V)
CONDITIONS
= 5V
RMS
RMS
RMS
CEN
CEN
= 5V, V
DC
DC
R
R
R
V
(500mA USB mode)
V
(100mA USB mode)
PEN1
PEN1
= 0V
= 5V
PSET
PSET
PSET
rising, 500mV hysteresis
rising, 360mV hysteresis
BATT
PEN1
BATT Continuous Current (total in two pins) ................. 2.4A
LDO Continuous Current ............................................. 50mA
LDO Short-Circuit Duration .........................................
Continuous Power Dissipation (T
Operating Temperature Range .......................... -40NC to +85NC
Junction Temperature ...................................... -40NC to +125NC
Storage Temperature ....................................... -65NC to +150NC
Lead Temperature (soldering, 10s) ................................+300NC
Soldering Temperature (reflow) ......................................+260NC
= 1.5kI
= 3kI
= 6.3kI
= 0V, V
= V
CEN
Single-Layer Board
Multilayer Board
= 4V, V
= 0V
PEN2
(derate 20.8mW/NC above +70NC) ......................1666.7mW
(derate 28.6mW/NC above +70NC) ......................2285.7mW
= 5V
PEN2
= 0V
THM
DC
= 5V
= 1.65V, USB, THMSW, CHG, DONE, OT, DOK,
falling,
1800
3.95
4.29
MIN
900
450
450
6.8
1.5
4.1
10
80
3
A
= +70NC)
2000
1000
TYP
4.35
195
475
475
100
4.0
6.9
0.8
0.2
1.5
3.3
50
95
50
1
5
A
= +25NC.) (Note 1)
MAX
2200
1100
Maxim Integrated
4.05
0.35
340
500
500
100
6.6
7.0
1.5
6.3
4.4
3.6
14
90
2
Continuous
UNITS
%/C
mA
mV
mA
ms
FA
kI
NC
Fs
I
V
V
V
V
V
V
RMS
RMS