MT46H64M16LFCK-6 IT:A TR Micron Technology Inc, MT46H64M16LFCK-6 IT:A TR Datasheet - Page 45

• Manufacturer Part Number: MT46H64M16LFCK-6 IT:A TR
• Description: IC DDR SDRAM 1GBIT 60VFBGA
• Manufacturer: Micron Technology Inc
• Type: DDR SDRAMr

Specifications of MT46H64M16LFCK-6 IT:A TR

• Format - Memory: RAM
• Memory Type: Mobile DDR SDRAM
• Memory Size: 1G (64M x 16)
• Speed: 166MHz
• Interface: Parallel
• Voltage - Supply: 1.7 V ~ 1.95 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 60-VFBGA
• Organization: 64Mx16
• Density: 1Gb
• Address Bus: 14b
• Access Time (max): 6.5/5.5ns
• Maximum Clock Rate: 166MHz
• Operating Supply Voltage (typ): 1.8V
• Package Type: VFBGA
• Operating Temp Range: -40C to 85C
• Operating Supply Voltage (max): 1.95V
• Operating Supply Voltage (min): 1.7V
• Supply Current: 115mA
• Pin Count: 60
• Mounting: Surface Mount
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 557-1335-2

Initialization
PDF: 09005aef82ce3074
1gb_ddr_mobile_sdram_t48m.pdf - Rev. K 07/09 EN
Prior to normal operation, the device must be powered up and initialized in a prede-
fined manner. Using initialization procedures other than those specified will result in
undefined operation.
If there is an interruption to the device power, the device must be re-initialized using
the initialization sequence described previously to ensure proper functionality of the
device.
To properly initialize the device, this sequence must be followed:
After steps 1–10 are completed, the device has been properly initialized and is ready to
receive any valid command.
10. Issue NOP or DESELECT commands for at least
1. The core power (V
2. When power supply voltages are stable and the CKE has been driven HIGH, it is
3. When the clock is stable, a 200μs minimum delay is required by the Mobile
4. Issue a PRECHARGE ALL command.
5. Issue NOP or DESELECT commands for at least
6. Issue an AUTO REFRESH command followed by NOP or DESELECT commands
7. Using the LOAD MODE REGISTER command, load the standard mode register as
8. Issue NOP or DESELECT commands for at least
9. Using the LOAD MODE REGISTER command, load the extended mode register to
It is recommended that V
must never exceed V
HIGH (see Figure 15 (page 46)). Alternatively, initialization can be completed
with CKE LOW provided that CKE transitions HIGH
(page 47)).
safe to apply the clock.
LPDDR prior to applying an executable command. During this time, NOP or DESE-
LECT commands must be issued on the command bus.
for at least
or DESELECT commands for at least
must be issued. Typically, both of these commands are issued at this stage as de-
scribed above.
desired.
the desired operating modes. Note that the sequence in which the standard and
extended mode registers are programmed is not critical.
t
RFC time. Issue a second AUTO REFRESH command followed by NOP
DD
DD
) and I/O power (V
. Standard initialization requires that CKE be asserted
45
DD
and V
1Gb: x16, x32 Mobile LPDDR SDRAM
Micron Technology, Inc. reserves the right to change products or specifications without notice.
DDQ
t
RFC time. Two AUTO REFRESH commands
be from the same power source, or V
DDQ
) must be brought up simultaneously.
t
t
t
RP time.
MRD time.
MRD time.
t
IS prior to T0 (see Figure 16
©2007 Micron Technology, Inc. All rights reserved.
Initialization
DDQ