AT24C02C-XHM-T Atmel, AT24C02C-XHM-T Datasheet - Page 20

• Manufacturer Part Number: AT24C02C-XHM-T
• Description: IC EEPROM 2KBIT 1MHZ 8TSSOP
• Manufacturer: Atmel

Specifications of AT24C02C-XHM-T

• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Memory Size: 2K (256 x 8)
• Speed: 400kHz, 1MHz
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 1.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Density: 2Kb
• Interface Type: Serial (2-Wire)
• Organization: 256x8
• Access Time (max): 550ns
• Frequency (max): 1MHz
• Write Protection: Yes
• Data Retention: 100Year
• Operating Supply Voltage (typ): 1.8/2.5/3.3/5V
• Package Type: TSSOP
• Operating Temp Range: -40C to 85C
• Supply Current: 3mA
• Operating Supply Voltage (min): 1.7V
• Operating Supply Voltage (max): 5.5V
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

20
5TS1 – SOT23
Atmel AT24C02C
Notes:
Package Drawing Contact:
[e-mail]
1. Dimensions D does not include mold flash, protrusions or gate
2. The package top may be smaller than the package bottom.
3. These dimensions apply to the flat section of the lead between
4. Dimension “b” does not include dambar protrusion. Allowable
5. This drawing is for general information only. Refer to JEDEC
burrs. Mold flash protrusions or gate burrs shall not exceed
0.15mm per end. Dimensions E1 does not include interlead flash or
protrusion. Interlead flasg or protrusion shall not exceed 0.15mm
per side.
Dimensions D and E1 are deteremined at the outermost extremes
of the plastic body exclusive of mold flash, tie bar burrs, gate burrs,
and interlead flash, but including any mismatch between the top
and bottom of the plastic body.
0.08mm and 0.15mm from the lead tip.
dambar protrusion shall be 0.80mm total in excess of the “b”
dimension at maximum material condition. The dambar cannot be
located on the lower radius of the foot. Minimum space between
protrusion and an adjacent lead shall not be less than 0.07mm.
Drawing MO-193, Variation AB for additional information.
SEATING
PLANE
E1
1
5
Top View
Side View
b
e1
D
2
TITLE
5TS1, 5-lead, 1.60mm Body, Plastic Thin
Shrink Small Outline Package (Shrink SOT)
e
3
4
A2
A1
E
A
SYMBOL
A
A1
A2
c
D
E
E1
L1
e
e1
b
COMMON DIMENSIONS
(Unit of Measure = mm)
0.00
0.70
0.08
0.30
MIN
End View
–
C
GPC
2.90 BSC
2.80 BSC
1.60 BSC
0.95 BSC
1.90 BSC
0.60 REF
TSZ
NOM
0.90
–
–
–
–
C
L1
L
DRAWING NO.
MAX
1.10
0.10
1.00
0.20
0.50
5TS1
8700D–SEEPR–8/10
NOTE
1, 2
1, 2
1, 2
3, 4
3
11/05/08
REV.
B