AT27C512R-70PU Atmel, AT27C512R-70PU Datasheet
AT27C512R-70PU
Specifications of AT27C512R-70PU
Available stocks
Related parts for AT27C512R-70PU
AT27C512R-70PU Summary of contents
Page 1
... OE) to give designers the flexibility to prevent bus contention. With 64K byte storage capability, the AT27C512R allows firmware to be stored reli- ably and to be accessed by the system without the delays of mass storage media. Atmel’s AT27C512R has additional features to ensure high quality and efficient pro- duction use ...
Page 2
... GND 14 15 2.2 32-lead PLCC Top View Note: PLCC Package Pins 1 and 17 are Don’t Connect. AT27C512R 2 Function Addresses Outputs Chip Enable Output Enable/ Program Supply No Connect 2.3 VCC A14 A13 A8 A9 A11 OE/VPP A10 A11 OE/VPP 24 A10 28-lead TSOP Top View – Type 1 ...
Page 3
... This is a stress rating only and func- tional operation of the device at these or any other conditions beyond those indicated in the opera- (1) tional sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. (1) (1) AT27C512R 3 ...
Page 4
... OE Outputs Ai ( ( Identification Code A15 = V IL and A0 which is toggled select the Device Code byte. AT27C512R -70 -40°C - 85°C -40° 125° ± 10% Min Max ±1 ±5 ±5 ±10 100 1 20 -0.6 0.8 2 0.5 CC 0.4 2.4 PP 0015O–EPROM–12/07 ...
Page 5
... Condition Whichever Occurred PP (1) = 0.8V and after the falling edge of CE without impact after the address is valid without impact on t ACC OE AT27C512R AT27C512R -45 -70 Min Max Min Max 0.0V and V = 3.0V. Timing mea 2.0V. Input AC drive levels are ...
Page 6
... Note 100 pF including jig capacitance, except for the -45 devices, where C L 13. Pin Capacitance ( MHz 25°C Symbol Typ OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. AT27C512R < (10 < (10 Max pF. L Units ...
Page 7
... Output High Voltage Supply Current (Program and Verify) CC2 CC I OE/V Current PP2 Product Identification Voltage ID 0015O–EPROM–12/07 (1) and 2.0V for 13.0 ± 0.25V PP Test Conditions 2 -400 µ AT27C512R Limits Min Max Units ±10 µA -0.6 0 0 11.5 12 ...
Page 8
... OE This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven – see timing diagram. 3. Program Pulse width tolerance is 100 µsec ± 5%. 17. Atmel’s AT27C512R Integrated Product Identification Code Codes A0 Manufacturer 0 ...
Page 9
... OE/V are read again and compared with the original data to determine if the device passes or fails. 0015O–EPROM–12/07 is raised to 13.0V. Each address is first programmed with one PP is then lowered AT27C512R is CC and V to 5.0V. All bytes IL CC ...
Page 10
... Ordering Code AT27C512R-45JI AT27C512R-45PI AT27C512R-45RI AT27C512R-45TI AT27C512R-70JI AT27C512R-70PI AT27C512R-70RI AT27C512R-70TI AT27C512R-70JA AT27C512R-70PA AT27C512R-70RA Ordering Code AT27C512R-45JU AT27C512R-45PU AT27C512R-45RU AT27C512R-45TU AT27C512R-70JU AT27C512R-70PU AT27C512R-70RU AT27C512R-70TU Package Type Package Operation Range 32J Industrial 28P6 (-40° 85° C) (1) 28R 28T 32J Industrial 28P6 (-40° 85° C) (1) ...
Page 11
... Lead coplanarity is 0.004" (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R 0015O–EPROM–12/07 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER TITLE 32J, 32-lead, Plastic J-leaded Chip Carrier (PLCC) AT27C512R 0.318(0.0125) 0.191(0.0075 COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM MAX SYMBOL A 3.175 – ...
Page 12
... PDIP A SEATING PLANE Notes: 1. This package conforms to JEDEC reference MS-011, Variation AB. 2. Dimensions D and E1 do not include mold Flash or Protrusion. Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). 2325 Orchard Parkway San Jose, CA 95131 R AT27C512R 12 D PIN 0º ~ 15º REF eB TITLE 28P6, 28-lead (0.600" ...
Page 13
... Mold Flash or protrusion shall not exceed 0.25 mm (0.010"). 2325 Orchard Parkway San Jose, CA 95131 R 0015O–EPROM–12/ TITLE 28R, 28-lead, 0.330" Body Width, Plastic Gull Wing Small Outline (SOIC) AT27C512R COMMON DIMENSIONS (Unit of Measure = mm) MIN MAX SYMBOL NOM A 2.39 – 2.79 A1 0.050 – 0.356 D 18 ...
Page 14
... E Notes: 1. This package conforms to JEDEC reference MO-183. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion 0.15 mm per side and 0.25 mm per side. 3. Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT27C512R 14 PIN SEATING PLANE A1 TITLE 28T, 28-lead (8 x 13.4 mm) Plastic Thin Small Outline Package, Type I (TSOP) 0º ...
Page 15
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...