MIKROE-793 mikroElektronika, MIKROE-793 Datasheet

Page 1

Best solution for fast and simple development of applications using ATxmega128A1 device. With special white plastic casing you can quickly turn your Ready for XMEGA project into a final product. for XMEGA ® ™ ...

Page 2

... TO OUR VALUED CUSTOMERS I want to express my thanks to you for being interested in our products and for having confidence in MikroElektronika. The primary aim of our company is to design and produce high quality electronic products and to constantly improve the performance thereof in order to better suit your needs. ...

Page 3

Table of Contents Introduction Package Contains Key Features 1. Power supply 2. ATxmega128A1 Microcontroller Key microcontroller features 3. Programming the microcontroller Programming with mikroBootloader mikroBootloader software Identifying device COM port step 1 – Choosing COM port step 2 – Establishing ...

Page 4

Introduction Ready for XMEGA Board is the best solution for fast and simple development of various microcontroller applications. It comes with ATxmega128A1, and contains double-row smart headers for all available microcontroller ports. We have groupped pins according to their functions, ...

Page 5

... Page 5 20122011 www.mikroe.com Copyright ©2011 Mikroelektronika. All rights reserved. Mikroelektronika, Mikroelektronika logo and other Mikroelektronika trademarks are the property of Mikroelektronika. All other tradmarks are the property of their respective owners. Unauthorised copying, hiring, renting, public performance and broadcasting of this DVD prohibited. ...

Page 6

Key Features System Specification power supply Via AC/DC connector 7-23V AC or 9-32V DC power consumption 50mA in idle state (when on-board modules are off) board dimensions 141 x 84mm (5.55 x 3.3 inch) weight ~67g (0.15 lbs) JTAG connector ...

Page 7

Page ...

Page 8

Power supply Figure 1-1: AC/DC adapter power supply connected Ready for XMEGA board can be powered in two ways: via USB connection, or using external power sources such as adapters and laboratory power supplies. USB connection can provide up ...

Page 9

VREF-1.8V VCC-3. OUT IN R15 2 GND 120K ADJ EN 10uF AP7331-ADJ R13 R14 22K 12K1 1.8V VOLTAGE REGULATOR VCC-5V VCC-5V L2 220uH R56 2K2 POWER E2 D6 LD1 C21 MBRS140T3 330uF/6V 220pF 5V ...

Page 10

ATxmega128A1 microcontroller Ready for XMEGA development ATxmega128A1 microcontroller. Having lots of MIPS power, flash and RAM, and rich set of inegrated modules, ATxmega128A1 is ideal choice for both beginners and professionals. Key microcontroller features 32 MIPS - Up to ...

Page 11

Programming the microcontroller Figure 3-1: ATxmega128A1 The microcontroller can be programmed in three ways: Via USB-UART mikroBootloader 01 Using JTAG external programmer 02 Using PDI external programmer 03 Page 11 ...

Page 12

... You can program the microcontroller with bootloader which is preprogrammed into the device by default. To transfer .hex file from MCU you need bootloader software USB HID) which can be downloaded from: http://www.mikroe.com/eng/downloads/get/1271/ mikrobootloader_xmega_v101.zip After software is downloaded, unrar desired location, and start mikroBootloader USB HID software. note This version of mikroBootloader is specialized for ATxmega128A1 chip ...

Page 13

Identifying device COM port Figure 3-3: Identifying COM port Device Manager Open window and expand 01 Ports section to see which COM port is assigned to Ready for XMEGA board (in this case COM34) step 1 – Choosing COM port ...

Page 14

Establishing Connection note: Baud rate is set to 115200bps by default. 01 Figure 3-5: Connecting with mikroBootloader Press ”Reset” button on Ready for XMEGA board and 01 ”Connect” click button within 5s, otherwise existing microcontroller program will ...

Page 15

Selecting .HEX file Figure 3-7: Locating and Selecting .hex file Select .HEX file using open dialog window. 01 Click the ”Open” button. 02 step 5 - Uploading .HEX file 01 02 Figure 3-8: Begin uploading To start ...

Page 16

Progress bar Figure 3-9: Progress bar You can monitor .HEX file uploading via progress bar. 01 step 7 - Finish upload 01 Figure 3-10: Restarting MCU Click 01 Press 02 and wait for 5 seconds. Your program ...

Page 17

Programming with JTAG programmer JTAG connector pads Ready for XMEGA board contains debugger. Before connecting the programmer you have to solder the provided pads. If bootloader program is accidentally erased, you can upload it again via AVR JTAG or PDI ...

Page 18

Programming with PDI programmer Figure 3-13: placing 6 pin header The board is also equipped with PDI connector pads, which allow you to program the microcontroller using external serial PDI programmer. Before attaching the programming connector, you have to solder ...

Page 19

AVCC PA6 1 PA6 PA7 2 PA7 3 GND 4 AVCC PB0 5 PB0 PB1 6 PB1 PB2 7 PB2 PB3 8 PB3 PB4/TMS 9 PB4 PB5/TDI 10 PB5 PB6/TCK 11 PB6 PB7/TDO 12 PB7 ATxmega128A1 13 GND 14 VCC ...

Page 20

USB-UART FTDI® chip Fast on-board allows you to communicate with other UART devices using USB-UART connection. USB-B connector (CN3) is used for connecting the USB cable. RX (receive) and TX (transmit) LEDs will indicate communication status. ...

Page 21

Prototyping area Figure 5-1: Proto area usage Figure 5-2: schematics of three LEDs connected to microcontroller pins as shown in Figure 5-1 with additional functionalities. That can be done by placing your additional components on available prototyping area. Pads ...

Page 22

Pin headers VCC-3.3V VCC-3.3V VCC-3.3V VCC-3.3V VCC-5V C6 C11 C12 C13 VCC-3.3V 100nF 100nF 100nF 100nF VCC-3.3V Decoupling capacitors VCC-5V VCC-5V VCC-5V AVCC PF3 PF3 PF2 PF2 PF1 PF1 PF0 PF0 PE7 PE7 PE6 PE6 PE5 PE5 PA6 1 ...

Page 23

Reset button VCC-3.3V R8 10K AVCC R9 T1 100 C7 100nF RESET 1 PA6 2 PA7 C3 22pF 3 GND 4 AVCC 5 PQ1/TOSC2 PB0 6 X2 PQ0/TOSC1 PB1 7 PB2 8 PB3 9 PB4 10 C4 22pF PB5 ...

Page 24

Piezo buzzer On-board piezo buzzer is a very useful module which can be used in debuging your code have audio signalization feature when board is integrated as a final product. Piezo buzzer’s resonant frequency is 3.8kHz. In ...

Page 25

Integrating with the casing Figure 9-1: Place the board into the bottom part of the casing. Make sure to align the connectors with the square openenings Ready for XMEGA can easily be integrated into the specialized white plastic casing. ...

Page 26

Dimensions (510 mils) 12.59 mm (360 mils) 9.14 mm (100 mils) 2.54 mm (4882 mils) 124 mm (5551 mils) 141 mm Page 26 (1839 mils) 46.7 mm (1268 mils) 32.2 mm (220 mils) (975 mils) 5.59 mm 24.76 mm ...

Page 27

... No part of this manual, including product and software described herein, may be reproduced, stored in a retrieval system, translated or transmitted in any form or by any means, without the prior written permission of MikroElektronika. The manual PDF edition can be printed for private or local use, but not for distribution. Any modification of this manual is prohibited. MikroElektronika provides this manual ‘ ...

Page 28

... If you want to learn more about our products, please visit our website at If you are experiencing some problems with any of our products or just need additional information, please place your ticket at If you have any questions, comments or business proposals, do not hesitate to contact us at www.mikroe.com www.mikroe.com/esupport office@mikroe.com Ready for XMEGA Manual ver. 1.00 0 100000 019061 ...