ZICM357SP2-1-B CEL, ZICM357SP2-1-B Datasheet - Page 11

• Manufacturer Part Number: ZICM357SP2-1-B
• Description: Zigbee / 802.15.4 Modules 2.4GHz, OP=20dBm Vdd 3.6Volt Max.
• Manufacturer: CEL

Specifications of ZICM357SP2-1-B

• Rohs: yes
• Frequency Band: 2.405 GHz to 2.48 GHz
• Data Rate: 250 Kbps
• Sensitivity: - 103 dBm
• Operating Supply Voltage: - 0.3 VDC to + 3.5 VDC
• Supply Current Transmitting: 58 mA
• Supply Current Receiving: 34 mA
• Output Power: 20 dBm
• Antenna Connector Type: PCB
• Dimensions: 0.94 in x 0.655 in

PROCESSING
Rework
The MeshConnect Module can be unsoldered from the host board. Use of a hot air rework tool should be programmable
and the solder joint and module should not exceed the maximum peak reflow temperature of 250 ºC.
Caution
If temperature ramps exceed the reflow temperature profile, module and component damage may occur due to thermal
shock. Avoid overheating.
Warning
Never attempt a rework on the module itself, (e.g. replacing individual components). Such actions will terminate warranty
coverage.
Additional Grounding
Attempts to improve module or system grounding by soldering braids, wires or cables onto the module RF shield cover is
done at the customer's own risk. The ground pins at the module perimeter should be sufficient for optimum immunity to
external RF interference.
AGENCY CERTIFICATIONS
The following Certifications are in effect:
ZICM357SP0-1: FCC, IC, CE
ZICM357SP2-1: FCC, IC
FCC Compliance Statement (Part 15.19) Section 7.15 of RSS-GEN
This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS Standards.
Operation is subject to the following two conditions:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
Warning (Part 15.21)
Changes or modifications not expressly approved by CEL could void the user's authority to operate the equipment.
20 cm Separation Distance
To comply with FCC/IC RF exposure limits for general population/uncontrolled exposure, the antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located
or operating in conjunction with any other antenna or transmitter.
OEM Responsibility to the FCC and IC Rules and Regulations
The MeshConnect Module has been certified per FCC Part 15 rules and to Industry Canada license-exempt RSS Stan-
dards for integration into products without further testing or certification. To fulfill the FCC and IC certification requirements,
the OEM of the MeshConnect Module must ensure that the information provided on the MeshConnect Label is placed on
the outside of the final product. The MeshConnect Module is labeled with its own FCC ID Number and IC ID Number. If the
FCC ID and the IC ID are not visible when the module is installed inside another device, then the outside of the device into
which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording
such as the following:
or
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
“Contains Transmitter Module FCC ID: W7Z-ZICM357SP0” or “Contains FCC ID: W7Z-ZICM357SP0”
“Contains Transmitter Module IC:8254A-ZICM357SP0" or "Contains IC: 8254A-ZICM357SP0”
“Contains Transmitter Module FCC ID: W7Z-ZICM357SP2” or “Contains FCC ID: W7Z-ZICM357SP2”
“Contains Transmitter Module IC: 8254A-ZICM357SP2" or "Contains IC: 8254A-ZICM357SP2”
d'en compromettre le fonctionnement.
(Continued)
(PCB ANTENNA ONLY)
MeshConnect™ EM357 Mini Modules
Page 11