M27C2001-10F1 STMicroelectronics, M27C2001-10F1 Datasheet
M27C2001-10F1
Specifications of M27C2001-10F1
Available stocks
Related parts for M27C2001-10F1
M27C2001-10F1 Summary of contents
Page 1
Features 5v ± 10% Supply Voltage in Read Operation Access Time: 35ns Low Power Consumption: – Active Current MHz – Standby Current: 100 µA Programming Voltage: 12.75V ± 0.25V Programming Time: 100 µs/word Electronic Signature – ...
Page 2
Contents Contents 1 Summary description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 3
M27C1001 List of tables Table 1. Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4
List of figures List of figures Figure 1. Logic Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 5
M27C1001 1 Summary description The M27C1001 Mbit EPROM offered in the two ranges: UV (ultra violet erase) and OTP (one time programmable ideally suited for microprocessor systems requiring large programs and is organized as 131,072 ...
Page 6
Summary description Table 1. Signal Descriptions Signal A0-A16 Q0- Figure 2. DIP Connections 6/24 Description Address Inputs Data Outputs Chip Enable Output Enable Program Program Supply Supply Voltage Ground Not ...
Page 7
M27C1001 Figure 3. LCC Connections Figure 4. TSOP Connections M27C1001 A11 A13 A14 M27C1001 25 (Normal) V ...
Page 8
... When in the standby mode, the outputs are in a high impedance state, independent of the G input. 2.3 Two-line output control Because EPROMs are usually used in larger memory arrays, this product features a 2-line control function which accommodates the use of multiple memory connection. The two line control function allows: the lowest possible memory power dissipation, complete assurance that output bus contention will not occur ...
Page 9
... M27C1001 ensures that all deselected memory devices are in their low power standby mode and that the output pins are only active when data is required from a particular memory device. 2.4 System considerations The power switching characteristics of Advanced CMOS EPROMs require careful decoupling of the devices. The supply current, I the system designer: the standby current level, the active current level, and transient current peaks that are produced by the falling and rising edges of E ...
Page 10
Device description Figure 5. Programming Flowchart 2.7 Program Inhibit Programming of multiple M27C1001s in parallel with different data is also easily accomplished. Except for E, all like inputs including G of the parallel M27C1001 may be common. A TTL low ...
Page 11
... M27C1001 Byte 0 ( represents the manufacturer code and byte 1 ( identifier code. For the STMicroelectronics M27C1001, these two identifier bytes are given in Table 3 and can be read-out on outputs Q7 to Q0. Table 3. Electronic Signature Identifier Manufacturer’s Code Device Code 2.10 Erasure operation (applies to UV EPROM) The erasure characteristics of the M27C1001 is such that erasure begins when the cells are exposed to light with wavelengths shorter than approximately 4000 Å ...
Page 12
... Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. 2. Depends on range. ...
Page 13
M27C1001 4 DC and AC characteristics 70°C, –40 to 85°C or –40 to 125° Table 5. Read Mode DC Characteristics Symbol I Input Leakage Current LI I Output Leakage Current LO I Supply Current ...
Page 14
DC and AC characteristics ° MHz A Table 7. Capacitance Symbol C Input Capacitance IN C Output Capacitance OUT 1. Sampled only, not 100% tested. Table 8. AC Measurement Conditions Parameter Input Rise and ...
Page 15
M27C1001 70°C, –40 to 85°C or –40 to 125° Table 9. Read Mode AC Characteristics Symbol Alt Address Valid AVQV ACC Output Valid Chip Enable Low t t ELQV CE to ...
Page 16
DC and AC characteristics 70°C, –40 to 85°C or –40 to 125° Table 10. Read Mode AC Characteristics Symbol Alt Address Valid AVQV ACC Output Valid Chip Enable Low t t ...
Page 17
M27C1001 ° 6.25V ± 0.25V Table 11. Programming Mode AC Characteristics Symbol Alt t t AVPL QVPL VPHPL VPS t t VCHPL VCS t t ELPL ...
Page 18
Package mechanical data 5 Package mechanical data 5.1 32-pin Ceramic Frit-seal DIP, with round window (FDIP32WA) Figure 10. FDIP32WA package outline Table 12. FDIP32WA package mechanical data Symbol ...
Page 19
M27C1001 5.2 32-pin Plastic DIP, 600 mils width (PDIP32) Figure 11. PDIP32 package outline Table 13. PDIP32 package mechanical data Symbol ...
Page 20
Package mechanical data 5.3 32-lead Rectangular Plastic Leaded Chip Carrier (PLCC32) Figure 12. PLCC32 package outline E3 Table 14. PLCC32 package mechanical data Symbol ...
Page 21
M27C1001 5.4 32-lead Plastic Thin Small Outline, 8x20 mm (TSOP32) Figure 13. TSOP32 package outline Table 15. TSOP32 package mechanical data Symbol 19.800 D1 18.300 N/2 ...
Page 22
... Options TR = ECOPACK® package, Tape & Reel Packing 1. High Speed, see AC Characteristics section for further information. For a list of available options (Speed, Package, etc...) or for further information on any aspect of this device, please contact the STMicroelectronics Sales Office nearest to you. 22/24 M27C1001 -10 = 100 ns ...
Page 23
M27C1001 7 Revision history Table 17. Document revision history Date September 1998 24-Jan-2000 20-Sep-2000 04-Jun-2002 12-Apr-2006 Revision 1 First Issue 2 35ns speed class addes (Table 8A, 3 AN620 Reference removed PLCC32 Package mechanical data and drawing clarified (Table 14 ...
Page 24
... Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...