LTC1734ES6-4.2#TRMPBF Linear Technology, LTC1734ES6-4.2#TRMPBF Datasheet - Page 10

• Manufacturer Part Number: LTC1734ES6-4.2#TRMPBF
• Description: IC BATT CHRGR LI-ION LIN SOT23-6
• Manufacturer: Linear Technology

Specifications of LTC1734ES6-4.2#TRMPBF

• Function: Charge Management
• Battery Type: Li-Ion, NiCd, NiMH
• Voltage - Supply: 4.55 V ~ 8 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: SOT-23-6 Thin, TSOT-23-6
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: LTC1734ES6-4.2#TRMPBFTR

APPLICATIONS
LTC1734
Once the maximum power dissipation and V
known, Table 1 can be used as a guide in selecting some
PNPs to consider. In the table, very low V
0.25V, low V
to 0.8V all depending on the current. See the manufacturer’s
data sheet for details. All of the PNP transistors are rated
to carry at least 1A continuously as long as the power
dissipation is within limits. The Stability section addresses
caution in the use of high beta PNPs.
Should overheating of the PNP transistor be a concern,
protection can be achieved with a positive temperature
coefficient (PTC) thermistor, wired in series with the
current programming resistor and thermally coupled to
the transistor. The PTH9C chip series from Murata has a
steep resistance increase at temperature thresholds from
85 C to 145 C making it behave somewhat like a thermo-
stat switch. For example, the model PTH9C16TBA471Q
thermistor is 470
resistance to 4.7k at 125 C. Below 125 C, the device
exhibits a small negative TC. The 470 thermistor can be
added in series with a 1.6k resistor to form the current
programming resistor for a 700mA charger. Should the
thermistor reach 125 C, the charge current will drop to
238mA and inhibit any further increase in temperature.
Stability
The LTC1734 contains two control loops: constant voltage
and constant current. To maintain good AC stability in the
10
Table 1. PNP Pass Transistor Selection Guide
Mounted on Board
Maximum P
10 (T
CESAT
at T
0.625
1 to 2
A
0.75
C
0.5
1.1
= 25 C
1
2
2
1
2
= 25 C)
is 0.25V to 0.5V and the others are 0.5V
U
D
(W)
at 25 C, but abruptly increase its
INFORMATION
U
Package Style
SOT-23-6
SOT-223
SOT-223
SOT-23
SOT-23
SOT-89
SOT-89
SOT-89
TO-252
FTR
ATV
W
CESAT
ZETEX Part Number
FCX589 or BCX69
BCP69 or FZT549
ZXT10P12DE6
is less than
CE(MIN)
U
FMMT549
FMMT720
FCX717
FZT589
are
constant voltage mode, a capacitor of at least 4.7 F is
usually required from BAT to ground. The battery and
interconnecting wires appear inductive at high frequen-
cies, and since these are in the feedback loop, this capaci-
tance may be necessary to compensate for the inductance.
This capacitor need not exceed 100 F and its ESR can
range from near zero to several ohms depending on the
inductance to be compensated. In general, compensation
is optimal with a capacitance of 4.7 F to 22 F and an ESR
of 0.5 to 1.5 .
Using high beta PNP transistors (>300) and very low ESR
output capacitors (especially ceramic) reduces the phase
margin, possibly resulting in oscillation. Also, using high
value capacitors with very low ESRs will reduce the phase
margin. Adding a resistor of 0.5 to 1.5 in series with
the capacitor will restore the phase margin.
In the constant current mode, the PROG pin is in the
feedback loop, not the battery. Because of this, capaci-
tance on this pin must be limited. Locating the program
resistor near the PROG pin and isolating the charge
current monitoring circuitry (if used) from the PROG pin
with a 1k to 10k resistor may be necessary if the capaci-
tance is greater than that given by the following equation:
ROHM Part Number
C
MAX pF
2SB1443
2SA1797
2SB1182
2SB822
( )
R
400
PROG
k
Comments
Low V
Very Low V
Very Low V
Very Low V
Low V
Low V
Low V
Low V
Low V
CESAT
CESAT
CESAT
CESAT
CESAT
CESAT,
CESAT,
CESAT,
CESAT,
High Beta
High Beta
High Beta, Small
High Beta