LTC4066EUF#TRPBF Linear Technology, LTC4066EUF#TRPBF Datasheet - Page 9

• Manufacturer Part Number: LTC4066EUF#TRPBF
• Description: IC USB POWER MANAGER 24-QFN
• Manufacturer: Linear Technology

Specifications of LTC4066EUF#TRPBF

• Function: Power Management
• Battery Type: Lithium-Ion (Li-Ion)
• Voltage - Supply: 4.35 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-WFQFN Exposed Pad
• Output Current: 1.5A
• Output Voltage: 4.2V
• Operating Supply Voltage (min): 4.35V
• Operating Supply Voltage (max): 5.5V
• Operating Temp Range: -40C to 85C
• Mounting: Surface Mount
• Pin Count: 24
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

SHDN (Pin 12): Shutdown Input. Pulling this pin greater
than 1.2V will disable the entire part and place it in a low
supply current mode of operation. All power paths will be
disabled. A weak pull-down current is internally applied
to this pin to ensure it is enabled at power-up when the
pin is not being driven externally.
HPWR (Pin 13): High Power Select. This logic input is used
to control the input current limit. A voltage greater than
1.2V on the pin will set the input current limit to 100% of
the current programmed by the CLPROG pin. A voltage
less than 0.4V on the pin will set the input current limit
to 20% of the current programmed by the CLPROG pin.
A weak pull-down current is internally applied to this pin
to ensure it is low at power-up when the pin is not being
driven externally.
NTC (Pin 14): Input to the NTC Thermistor Monitoring
Circuits. Under normal operation, tie a thermistor from
the NTC pin to ground and a resistor of equal value from
NTC to V
• V
the timer is suspended, but not cleared, the charging is
disabled and the CHRG pin remains in its former state.
When the voltage on NTC comes back between 0.74 •
V
off and charging is re-enabled if the battery voltage is
below the recharge threshold. There is approximately 3°C
of temperature hysteresis associated with each of the input
comparators. Connect the NTC pin to ground to disable
this feature. This will disable all of the LTC4066/LTC4066-1
NTC functions.
V
this pin to the NTC pin will bias the NTC thermistor.
GND (Pin 16), Exposed Pad (Pin 25): Ground. The Exposed
Pad is ground and must be soldered to the PC board for
maximum heat transfer. The Exposed Pad must be electri-
cally connected to the GND pin.
PIN FUNCTIONS
VNTC
NTC
VNTC
(Pin 15): Output Bias Voltage for NTC. A resistor from
and 0.29 • V
(Cold, 0°C) or below 0.29 • V
NTC
. When the voltage on this pin is above 0.74
VNTC
, the timer continues where it left
VNTC
(Hot, 50°C)
ACPR (Pin 17): Wall Adapter Present Output. Active low
open-drain output pin. A low on this pin indicates that the
wall adapter input comparator has had its input pulled
above the input threshold. This feature is disabled if the
part is shut down or if no power is present on IN or OUT
or BAT (i.e., below UVLO thresholds).
CHRG (Pin 18): Open-Drain Charge Status Output. When
the battery is being charged, the CHRG pin is pulled low by
an internal N-channel MOSFET. When the timer runs out or
the charge current drops below a programmable current
level or the input supply or output supply is removed, the
CHRG pin is forced to a high impedance state.
POL (Pin 19): Battery Current Status Polarity Pin. This
open-drain output pin indicates whether the current fl owing
out of the I
rent fl owing into or out of the BAT pins. The POL pin will
pull down when current is fl owing out of the BAT pin (i.e.,
charging) and will assume a high impedance state when
current is fl owing into the BAT pin (i.e., ideal diode).
WALL (Pin 20): Wall Adapter Present Input. Pulling this
pin above 1.225V will disconnect the power path from IN
to OUT. The ACPR pin will also be pulled low to indicate
that a wall adapter has been detected.
TIMER (Pin 21): Timer Capacitor. Placing a capacitor,
C
is:
Charge time is increased if charge current is reduced due
to load current, thermal regulation and current limit selec-
tion (HPWR). Shorting the TIMER pin to GND disables the
battery charging functions.
TIMER
t
TIMER
, to GND sets the timer period. The timer period
(
STAT
Hours
pin represents one-thousandth of the cur-
LTC4066/LTC4066-1
)
=
C
TIMER
0 1
.
•
R
μ
PROG
F
•
100
•
3
k
Hours
4066fc
9