LTC4011CFE Linear Technology, LTC4011CFE Datasheet - Page 14

• Manufacturer Part Number: LTC4011CFE
• Description: IC BATT CHARGER HIEFF 20TSSOP
• Manufacturer: Linear Technology

Specifications of LTC4011CFE

• Function: Charge Management
• Battery Type: Nickel Cadmium (NiCd), Nickel Metal-Hydride (NiMH)
• Voltage - Supply: 4.5 V ~ 34 V
• Operating Temperature: 0°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-TSSOP (0.173", 4.40mm Width) Exposed Pad
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

LTC4011
operaTion
PWM Current Source Controller
An integral part of the LTC4011 is the PWM current source
controller. The charger uses a synchronous step-down
architecture to produce high efficiency and limited thermal
dissipation. The nominal operating frequency of 550kHz
allows use of a smaller external filter components. The
TGATE and BGATE outputs have internally clamped volt-
age swings. They source peak currents tailored to smaller
surface-mount power FETs likely to appear in applications
providing an average charge current of 3A or less. During
the various charging states, the LTC4011 uses the PWM
controller to regulate an average voltage between SENSE
and BAT that ranges from 10mV to 100mV.
A conceptual diagram of the LTC4011 PWM control loop
is shown in Figure 2.
The voltage across the external current programming
resistor R
EA. An internal programming current is also pulled from
input resistor R1. The I
desired average voltage drop across R
the average current through R
the error amplifier is a scaled control current for the input

R
N
SENSE
P
V
CC
SENSE
17
15
11
12
LTC4011
Figure 2. LTC4011 PWM Control Loop
TGATE
BGATE
SENSE
BAT
is averaged by integrating error amplifier
R1
R2
PROG
I
–
+
PROG
• R1 product establishes the
Q
EA
SENSE
R
S
R3
R4
. The I
SENSE
PWM CLOCK
I
TH
TH
, and hence,
CC
output of
4011 F02
of the PWM comparator CC. The I
peak current threshold for CC such that the desired aver-
age current through R
comparator output does this by switching the state of the
SR latch at the appropriate time.
At the beginning of each oscillator cycle, the PWM clock
sets the SR latch and the external P-channel MOSFET is
switched on (N-channel MOSFET switched off) to refresh
the current carried by the external inductor. The inductor
current and voltage drop across R
linearly. During normal operation, the PFET is turned
off (NFET on) during the cycle by CC when the voltage
difference across R
the output of EA. The inductor current then ramps down
linearly until the next rising PWM clock edge. This closes
the loop and maintains the desired average charge current
in the external inductor.
Low Dropout Charging
After charging is initiated, the LTC4011 does not require
that V
ations exist where low dropout charging might occur. In
one instance, parasitic series resistance may limit PWM
headroom (between V
reached. A second case can arise when the DC adapter
selected by the end user is not capable of delivering the
current programmed by R
age of the adapter to collapse. While in low dropout, the
LTC4011 PWM runs near 100% duty cycle with a frequency
that may not be constant and can be less than 550kHz.
The charge current will drop below the programmed value
to avoid generating audible noise, so the actual charge
delivered to the battery may depend primarily on the
LTC4011 charge timer.
Internal Die Temperature
The LTC4011 provides internal overtemperature detection
to protect against electrical overstress, primarily at the
FET driver outputs. If the die temperature rises above this
thermal limit, the LTC4011 stops switching and indicates
a fault as previously discussed.
CC
remain at least 500mV above BAT because situ-
SENSE
CC
SENSE
and BAT) as 100% charge is
reaches the peak value set by
SENSE
is maintained. The current
, causing the output volt-
TH
• R3 product sets a
SENSE
begin to rise
4011fb