TC7136ACPL Microchip Technology, TC7136ACPL Datasheet - Page 14

• Manufacturer Part Number: TC7136ACPL
• Description: IC ADC 3 1/2DGT LOW PWR 40-DIP
• Manufacturer: Microchip Technology

Specifications of TC7136ACPL

• Display Type: LCD
• Configuration: 7 Segment
• Digits Or Characters: A/D 3.5 Digits
• Current - Supply: 70µA
• Voltage - Supply: 9V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Package / Case: 40-DIP (0.600", 15.24mm)
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification
• Interface: -

TC7136/TC7136A
The TC7136/A connects the internal V
inputs to analog common during the auto-zero phase.
During the reference integrate phase, V
to analog common. If V
analog common, a Common mode voltage exists, but
is rejected by the converter's 86dB Common mode
rejection ratio. In battery operation, analog common
and V
mode voltage concerns. In systems where V
nected to the power supply ground or to a given
voltage, analog common should be connected to V
The analog common pin serves to set the analog sec-
tion reference, or common point. The TC7136A is spe-
cifically designed to operate from a battery, or in any
measurement system where input signals are not refer-
enced (float), with respect to the TC7136A power
source. The analog common potential of V+ – 3V gives
a 7V end of battery life voltage. The common potential
has a 0.001%/% voltage coefficient.
With
(V+ – V- > 7V), analog common is a very stable poten-
tial with excellent temperature stability (typically
35ppm/°C for TC7136A. This potential can be used to
generate the TC7136A's reference voltage. An external
voltage reference will be unnecessary in most cases,
because of the 35ppm/°C temperature coefficient. See
Section 7.5, TC7136A Internal Voltage Reference
discussion.
7.4
The TEST pin potential is 5V less than V
be used as the negative power supply connection for
external CMOS logic. The TEST pin is tied to the inter-
nally generated negative logic supply through a 500Ω
resistor. The TEST pin load should not be more than
1mA. See Section 8.0, Typical Applications for addi-
tional information on using TEST as a negative digital
logic supply.
If TEST is pulled high (to V+), all segments plus the
minus sign will be activated. DO NOT OPERATE IN
THIS MODE FOR MORE THAN SEVERAL MINUTES.
With TEST = V+, the LCD segments are impressed with
a DC voltage which will destroy the LCD.
7.5
The TC7136 analog common voltage temperature sta-
bility has been significantly improved (Figure 7-3). The
"A" version of the industry standard TC7136 device
allows users to upgrade old systems and design new
systems without external voltage references. External
R and C values do not need to be changed; however,
noise performance will be improved by increasing C
(see Section 6.1, Auto-Zero Capacitor). Figure 7-4
shows analog common supplying the necessary
voltage reference for the TC7136/A.
DS21461C-page 14
IN
sufficiently
- are usually connected, removing Common
TEST (Pin 37)
TC7136A Internal Voltage
Reference
high
IN
- is not externally connected to
total
supply
IN
- is connected
IN
+
. TEST may
+ and V
IN
- is con-
voltage
IN
IN
AZ
-.
-
FIGURE 7-3:
FIGURE 7-4:
200
180
160
140
120
100
80
60
40
20
0
Set V
26
V-
TC7136A
Maximum
TC7136A
REF
TC7136
Typical
COMMON
ANALOG
9V
= 1/2 V
V
V
+
REF
ANALOG COMMON
TEMPERATURE
COEFFICIENT
TC7136A INTERNAL
VOLTAGE REFERENCE
CONNECTION
REF
© 2005 Microchip Technology Inc.
V+
+
REF
1
-
Maximum
36
35
32
V
TC7136
Typical
REF
240kΩ
10kΩ
No Maximum
Specified
ICL7136
Typical