MIC2586-1YM Micrel Inc, MIC2586-1YM Datasheet
MIC2586-1YM
Specifications of MIC2586-1YM
MIC2586-1YM
Available stocks
Related parts for MIC2586-1YM
MIC2586-1YM Summary of contents
Page 1
... General-purpose hot board insertion • High-voltage, high-side electronic circuit breaker • +12V/+24V/+48V Distributed Power Systems • +24V/+48V Industrial/Alarm Systems • Telecom Systems • Medical systems PWRGD Polarity Pb-Free MIC2586-1YM Active-HIGH MIC2586-2YM Active-LOW MIC2586R-1YM Active- HIGH MIC2586R-2YM Active-LOW ...
Page 2
... MIC2586R-1BM Power, Connect and Protect is a trademark of Micrel, Inc Micrel, Inc • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax +1 (408) 474-1000 • http://www.micrel.com October 2004 MIC2586/86R Typical Application Circuit 2 MIC2586/MIC2586R 14-Pin SOIC (M) ...
Page 3
... FBH threshold, PWRGD (or /PWRGD) is deasserted. The FB comparator exhibits a typical hysteresis of 80mV. The FB pin voltage also affects the MIC2586/MIC2586R’s foldback current limit operation (see the “Functional Description” section for further information). Power-is-Good (PWRGD1 or /PWRGD1), Open-drain Output: This pin remains deasserted during start up while the FB pin voltage is below the V Once the voltage at the FB pin rises above the V Good output asserts with minimal delay (typically ≤ ...
Page 4
... TIMERUP capacitor is discharged by the I TIMERDN TIMER pin is less than 0.5V, the MIC2586 can be restarted by toggling the ON pin LOW then HIGH. For the MIC2586R, the capacitor connected to the TIMER pin sets the period of auto-retry where the duty cycle is fixed at a nominal 5%. ...
Page 5
... SENSE pin and the VCC pin can be tied together. Positive Supply Voltage Input: This pin is the (+) Kelvin sense connection for the output supply rail. The nominal operating voltage range for the MIC2586 and the MIC2586R is +10V to +80V, and VCC can withstand input transients up to +100V ...
Page 6
... TRIP 1.8 GATE[TH] -24 -65 TRIP 1.5 3.5 TRIP 1.280 1.313 MIC2586/MIC2586R Max Units 8 1.345 V 1.258 V mV 0.05 mV/V µ µA -22 200 mA mA µA -120 µA 5 1.345 ...
Page 7
... I Power-Good Leakage Current OFF Power-Good Delay Capacitor Charging I CPG Current V PGTIMER Threshold Voltage to Assert PG2 PWRGD2 (MIC2586/86R-1) or /PWRGD2 (MIC2586/86R-2) V PGTIMER Threshold Voltage to Assert PG3 PWRGD3 (MIC2586/86R-1) or /PWRGD2 (MIC2586/86R-2) AC Electrical Characteristics V = +24V and +48V 25°C, unless otherwise noted. BOLD indicates specifications apply over the full operating temperature range of - ...
Page 8
... Figure 1. Foldback Current Limit Transfer Characteristic Figure GATE Timing Figure 3. MIC2586/86R PWRGD1 Timing Power, Connect and Protect is a trademark of Micrel, Inc Micrel, Inc • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax +1 (408) 474-1000 • http://www.micrel.com October 2004 Figure 4 ...
Page 9
... Micrel Functional Characteristics October 2004 MIC2586/MIC2586R Block Diagram 9 MIC2586/MIC2586R M9999-102204 (408) 955-1690 ...
Page 10
... V in the datasheet and R (1) sense resistor. As the MIC2586 and the MIC2586R employ a constant-current regulation scheme in current limit, the charge pump’s output voltage at the GATE pin is adjusted so that the voltage across the external sense resistor is held equal to V pin is being charged ...
Page 11
... I OUT LIMIT October 2004 An initial value for C will take for the MIC2586/MIC2586R to completely charge up the output capacitive load. Assuming the load is enabled by the PWRGDx (or /PWRGDx) signal(s) of the controller, the turn-on delay time is derived from the following expression × (dV/dt): ...
Page 12
... AUTO-RESTART Input Undervoltage Lockout The MIC2586/MIC2586R have an internal undervoltage lockout circuit that inhibits operation of the controller’s internal circuitry unless the power supply voltage is stable and within an acceptable tolerance. If the supply voltage to the controller with respect to ground is greater than the V threshold voltage (8V typical), the controller’ ...
Page 13
... Micrel Applications Information External ON/OFF Control The MIC2586/MIC2586R have an ON pin input that is used to enable the controller to commence a start-up sequence upon card insertion or to disable controller operation upon card removal. In addition, the ON pin can be used to reset the MIC2586/MIC2586R’s internal electronic circuit breaker in the event of a load current fault ...
Page 14
... I ( HOT_SWAP(MAX) 0.97 ×R SENSE(NOM) In this case, the application circuit must be sturdy enough to operate over a ~1.5-to-1 range in hot swap load currents. For example MIC2586 circuit must pass a minimum hot swap load current of 4A without nuisance trips set to: 39mV = = Ω R 9.75m SENSE(NOM) 4A where the nearest 1% standard value is 9.76mΩ ...
Page 15
... Device types, part numbers, and manufacturer contacts for power MOSFETs and sense resistors are provided in Table 1. Figure 10. Recommended PCB Layout for Sense Resistor, Power MOSFET, Timer and Feedback Network. October 2004 Figure 9. Current Limit Sense Filter for Noisy Systems 15 MIC2586/MIC2586R M9999-102204 (408) 955-1690 ...
Page 16
... Series www.vishay.com/docswsl_30100.pdf (203) 452-5664 “OARS” Series www.irctt.com/pdf_files/OARS.pdf “LR” Series www.irctt.com/pdf_files/LRC.pdf second source to “WSL” (828) 264-8861 Table 1. MOSFET and Sense Resistor Vendors 16 MIC2586/MIC2586R ) Contact Information DSS www.siliconix.com (203) 452-5664 www.siliconix.com (203) 452-5664 www.irf.com (310) 322-3331 www.renesas.com ...
Page 17
... INCHES (MM) 0.050 (1.27) 0.016 (0.40) TYP TYP 0.006 (0.15) 0.344 (8.75) 0.337 (8.55) SEATING PLANE 14-Pin SOIC (M) damages resulting from such use or sale. © 2004 Micrel, Incorporated. 17 MIC2586/MIC2586R 0.193 (4.90) 45° 3°–6° 0.244 (6.20) 0.228 (5.80) M9999-102204 (408) 955-1690 ...