CAT3644HV3-GT2 ON Semiconductor, CAT3644HV3-GT2 Datasheet - Page 9

• Manufacturer Part Number: CAT3644HV3-GT2
• Description: IC LED DVR 4CH QUAD MODE 16TQFN
• Manufacturer: ON Semiconductor
• Series: QUAD-Mode®r
• Type: Backlight, White LEDr

Specifications of CAT3644HV3-GT2

• Topology: Linear (LDO), Switched Capacitor (Charge Pump)
• Number Of Outputs: 4
• Internal Driver: Yes
• Type - Primary: Backlight
• Type - Secondary: White LED
• Frequency: 800kHz ~ 1.6MHz
• Voltage - Supply: 2.5 V ~ 5.5 V
• Voltage - Output: 7V
• Mounting Type: Surface Mount
• Package / Case: 16-TFQFN Exposed Pad
• Operating Temperature: -40°C ~ 85°C
• Current - Output / Channel: 25mA
• Internal Switch(s): Yes
• Efficiency: 92%
• Number Of Digits: 4
• Low Level Output Current: 25 mA
• High Level Output Current: 100 mA
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Supply Current: 30 mA
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Pin Function
VIN is the supply pin for the charge pump. A small 1 mF
ceramic bypass capacitor is required between the VIN pin
and ground near the device. The operating input voltage
range is from 2.5 V to 5.5 V. Whenever the input supply falls
below the under−voltage threshold (1.8 V), all the LED
channels are disabled and the device enters shutdown mode.
EN/DIM is the enable and one wire dimming input for all
LED channels. Levels of logic high and logic low are set at
1.3 V and 0.4 V respectively. When EN/DIM is initially
taken high, the device becomes enabled and all LED
currents are set to the full scale according to the resistor
R
mode, the EN/DIM pin must be held low for at least 1.5 ms.
VOUT is the charge pump output that is connected to the
LED anodes. A small 1 mF ceramic bypass capacitor is
required between the V
GND is the ground reference for the charge pump. The pin
must be connected to the ground plane on the PCB.
Table 6. PIN DESCRIPTION
SET
Pin #
. To place the device into “zero current” shutdown
TAB
10
12
13
14
15
16
11
1
2
3
4
5
6
7
8
9
EN/DIM
Name
RSET
VOUT
LED2
LED3
LED4
LED1
GND
GND
C1+
C1−
C2+
C2−
VIN
NC
NC
NC
OUT
pin and ground near the device.
LED2 cathode terminal.
LED3 cathode terminal.
LED4 cathode terminal.
Connect resistor RSET to set the LED current.
Device enable (active high) and Dimming Control.
Charge pump output connected to the LED anodes.
Not connected inside the package.
Charge pump input, connect to battery or supply.
Bucket capacitor 1 Positive terminal
Bucket capacitor 1 Negative terminal
Bucket capacitor 2 Positive terminal
Bucket capacitor 2 Negative terminal
Not connected inside the package.
Not connected inside the package.
Ground Reference
LED1 cathode terminal.
Connect to GND on the PCB.
http://onsemi.com
9
C1+, C1− are connected to each side of the ceramic bucket
capacitor C
C2+, C2− are connected to each side of the ceramic bucket
capacitor C
LED1 to LED4 provide the internal regulated current
source for each of the LED cathodes. These pins enter
high−impedance zero current state whenever the device is
placed in shutdown mode.
TAB is the exposed pad underneath the package. For best
thermal performance, the tab should be soldered to the PCB
and connected to the ground plane.
RSET is connected to the resistor (R
current for the LEDs. The voltage at this pin regulated to
0.6 V. The ground side of the external resistor should be star
connected back to the GND of the PCB. In shutdown mode,
RSET becomes high impedance.
Function
1
2
.
.
SET
) to set the full scale