TC4468CPD Microchip Technology, TC4468CPD Datasheet - Page 3

• Manufacturer Part Number: TC4468CPD
• Description: IC MOSFET DVR QUAD AND 14DIP
• Manufacturer: Microchip Technology
• Type: Microcontrollerr

Specifications of TC4468CPD

• Number Of Outputs: 4
• Package / Case: 14-DIP (0.300", 7.62mm)
• Configuration: Low-Side
• Input Type: AND
• Delay Time: 40ns
• Current - Peak: 1.2A
• Number Of Configurations: 4
• Voltage - Supply: 4.5 V ~ 18 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Rise Time: 25 ns
• Fall Time: 25 ns
• Supply Voltage (min): 4.5 V
• Supply Current: 4 mA
• Maximum Power Dissipation: 800 mW
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: 0 C
• Number Of Drivers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• High Side Voltage - Max (bootstrap): -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 158-1119; 158-1119; TC4468CPDR; TC4468CPDR

1.0
Absolute Maximum Ratings†
Supply Voltage ...............................................................+20 V
Input Voltage ............................. (GND – 5 V) to (V
Package Power Dissipation: (T
Package Thermal Resistance:
Operating Temperature Range:
Maximum Chip Temperature ....................................... +150°C
Storage Temperature Range.........................-65°C to +150°C
ELECTRICAL SPECIFICATIONS
Electrical Characteristics: Unless otherwise noted, T
Input
Logic 1, High Input Voltage
Logic 0, Low Input Voltage
Input Current
Output
High Output Voltage
Low Output Voltage
Output Resistance
Peak Output Current
Continuous Output Current
Latch-Up Protection Withstand
Reverse Current
Switching Time (Note 1)
Rise Time
Fall Time
Delay Time
Delay Time
Power Supply
Power Supply Current
Power Supply Voltage
Note
2002 Microchip Technology Inc.
PDIP...................................................................800 mW
CERDIP .............................................................840 mW
SOIC ..................................................................760 mW
CERDIP R
CERDIP R
PDIP R
PDIP R
SOIC R
SOIC R
C Version ................................................... 0°C to +70°C
E Version.................................................-40°C to +85°C
M Version ..............................................-55°C to +125°C
1:
2:
3:
ELECTRICAL
CHARACTERISTICS
Totem pole outputs should not be paralleled because the propagation delay differences from one to the other could cause one driver to
drive high a few nanoseconds before another. The resulting current spike, although short, may decrease the life of the device. Switching
times are ensured by design.
When driving all four outputs simultaneously in the same direction, V
will cause high-power dissipation in the device.
The input threshold has approximately 50 mV of hysteresis centered at approximately 1.5 V. Input rise times should be kept below 5 µsec
to avoid high internal peak currents during input transitions. Static input levels should also be maintained above the maximum, or below
the minimum, input levels specified in the "Electrical Characteristics" to avoid increased power dissipation in the device.
Parameters
J-A
J-C
J-A
J-C
J-A
J-C
..........................................................80°C/W
..........................................................35°C/W
..........................................................95°C/W
..........................................................28°C/W
...................................................100°C/W
.....................................................23°C/W
A
70°C)
Sym
V
V
V
V
V
R
I
I
t
t
I
PK
DC
t
t
D1
D2
I
IN
OH
DD
OL
IH
I
R
F
S
IL
O
V
DD
DD
+ 0.3 V)
Min
-1.0
2.4
– 0.025
4.5
—
—
—
—
—
—
—
—
—
—
—
—
A
= +25°C, with 4.5 V
TC4467/TC4468/TC4469
Typ
500
1.2
1.5
—
—
—
—
—
10
—
—
15
15
40
40
—
†Notice: Stresses above those listed under "Maximum
Ratings" may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operation listings of this specification is not implied. Exposure
to maximum rating conditions for extended periods may affect
device reliability.
DD
will be limited to 16 V. This reduces the chance that internal dv/dt
Max
V
+1.0
0.15
300
500
0.8
15
25
25
75
75
18
—
—
—
DD
4
V
DD
Units
nsec
nsec
nsec
nsec
mA
mA
mA
µA
V
V
V
V
A
V
18 V.
Note 3
Note 3
0 V
I
I
I
Single Output
Total Package
4.5 V
Figure 4-1
Figure 4-1
Figure 4-1
Figure 4-1
Note 2
LOAD
LOAD
OUT
= 10 mA, V
V
= 100 µA (Note 1)
= 10 mA (Note 1)
IN
V
DD
V
DD
Conditions
16 V
DD
= 18 V
DS21425B-page 3