IC DRIVER REVERSE MOTOR HSIP10

BA6219B

Manufacturer Part NumberBA6219B
DescriptionIC DRIVER REVERSE MOTOR HSIP10
ManufacturerRohm Semiconductor
BA6219B datasheet
 

Specifications of BA6219B

ApplicationsDC Motor DriverNumber Of Outputs1
Current - Output1.7AVoltage - Supply8 V ~ 18 V
Operating Temperature-20°C ~ 75°CMounting TypeThrough Hole
Package / Case10-SIP + TabLead Free Status / RoHS StatusLead free / RoHS Compliant
Voltage - Load-  
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
Page 1/7

Download datasheet (102Kb)Embed
Next
Motor driver ICs
Reversible motor driver
BA6219B / BA6219BFP-Y
The BA6219B and BA6219BFP-Y are reversible-motor drivers suitable for brush motors. Two logic inputs allow four out-
put modes: forward, reverse, idling, and braking. The motor revolving speed can be set arbitrarily by controlling the volt-
age applied to the motor.
FApplications
VCRs and cassette tape recorders
FFeatures
1) Large output current. (I
=2.2A Max.)
O
2) Built-in thermal shutdown circuit.
FBlock diagram
398
3) Built-in output voltage setting pins.
4) Small standby supply current.

BA6219B Summary of contents

  • Page 1

    ... Reversible motor driver BA6219B / BA6219BFP-Y The BA6219B and BA6219BFP-Y are reversible-motor drivers suitable for brush motors. Two logic inputs allow four out- put modes: forward, reverse, idling, and braking. The motor revolving speed can be set arbitrarily by controlling the volt- age applied to the motor. ...

  • Page 2

    ... Motor driver ICs FAbsolute maximum ratings (Ta = 25_C) FRecommended operating conditions (Ta = 25_C) FElectrical characteristics (unless otherwise noted 25_C and V FElectrical characteristic curves BA6219B / BA6219BFP-Y = 12V) CC 399 ...

  • Page 3

    ... Motor driver ICs FMeasurement circuits FInput / output truth table 400 BA6219B / BA6219BFP-Y ...

  • Page 4

    ... Motor driver ICs FPin descriptions (BA6219BFP-Y) BA6219B / BA6219BFP-Y (BA6219B) 401 ...

  • Page 5

    ... When the output voltage control pin (pin 4) is used V < CC1 * 2.5V V < {(V R CC2 (Q6) (2) When the output voltage control pin (pin 4) is not used, V (5) Input circuit BA6219B / BA6219BFP SAT (Q1) BE (Q5) BE (Q6) BE (Q7 SAT (Q3) BE (Q3) BE (Q2 (Q7) CC2 is either short-circuited left OPEN ...

  • Page 6

    ... There are no circuits built into these ICs that pre- vent in-rush currents. Therefore recommended to place a current limiting resistor or other physical counter- measure. BA6219B / BA6219BFP-Y (14) If the potential of the output pin sways greatly and goes below the potential of ground, the operation of the IC may malfunction or be adversely affected. In such a case, place a diode between the output and ground, or other measure, to prevent this ...

  • Page 7

    ... A resistance range of 3X10 is recommended Power supply filtering capacitor. Place as near as possible to the V pin. CC1 CD : Capacitor to prevent both output transistors being turned on at the same time Capacitor to absorb surge voltage and prevent parasitic oscillations. FExternal dimensions (Units: mm) 404 BA6219B / BA6219BFP-Y (2) BA6219BFP-Y ...