AD7817ARZ Analog Devices Inc, AD7817ARZ Datasheet - Page 14

• Manufacturer Part Number: AD7817ARZ
• Description: IC ADC 10BIT 4CH W/TEMP 16-SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD7817ARZ

• Function: Temp Monitoring System (Sensor)
• Topology: ADC, Multiplexer, Register Bank
• Sensor Type: Internal
• Sensing Temperature: -40°C ~ 85°C
• Output Type: MICROWIRE™, QSPI™, SPI™
• Output Alarm: Yes
• Output Fan: Yes
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (3.9mm Width)
• Resolution (bits): 10bit
• Sampling Rate: 100kSPS
• Input Channel Type: Single Ended
• Data Interface: Serial
• Supply Voltage Range - Analog: 2.7V To 5.5V
• Supply Current: 1.6mA
• Digital Ic Case Style: SOIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD7816/7/8EB - BOARD EVALUATION FOR AD7816/7/8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

AD7816/AD7817/AD7818
Figure 14. Self-Heating Effect in Air, Fluid, and in Thermal
Contact with a Heat Sink
Figure 15. Self-Heating Effect in Air, Fluid, and in Thermal
Contact with a Heat Sink
–0.05
–0.01
0.25
0.20
0.15
0.10
0.05
0.00
0.8
0.7
0.6
0.5
0.4
0.2
0.0
0.3
0.1
0.0
0
2
CONVST
RD/ WR
BUSY
SCLK
D
0.5
OTI
OUT
4
D
CS
IN
6
AIR
TIME – secs
FLUID
AIR
TIME – secs
1.0
8
HEAT SINK
10
DB7 – DB0
1.5
12
FLUID
HEATSINK
14
Figure 16. Mode 1 Operation
t
17
t
2.0
3
16
t
2
t
–14–
1
OPERATING MODES
The AD7816, AD7817, and AD7818 have two possible modes
of operation depending on the state of the CONVST pulse at
the end of a conversion.
Mode 1
In this mode of operation the CONVST pulse is brought high
before the end of a conversion, i.e., before the BUSY goes low
(see Figure 16). When operating in this mode a new conversion
should not be initiated until 100 ns after the end of a serial read
operation. This quiet time is to allow the track/hold to accu-
rately acquire the input signal after a serial read.
Mode 2
When the AD7816, AD7817, and AD7818 are operated in Mode
2 (see Figure 17), they automatically power down at the end of
a conversion. The CONVST is brought low to initiate a conver-
sion and is left logic low until after the end of the conversion. At
this point, i.e., when BUSY goes low, the devices will power-
down. The devices are powered up again on the rising edge of
the CONVST signal. Superior power performance can be
achieved in this mode of operation by powering up the AD7816,
AD7817, and AD7818 only to carry out a conversion (see Power
vs. Throughput section). In Figure 17 the CS line is applicable
to the AD7817 only.
t
15
t
16
DB7(DB9) – DB0
REV. C