MAX6690MEE+ Maxim Integrated Products, MAX6690MEE+ Datasheet - Page 6

• Manufacturer Part Number: MAX6690MEE+
• Description: IC TEMP SENSOR SMBUS 16-QSOP
• Manufacturer: Maxim Integrated Products

Specifications of MAX6690MEE+

• Function: Thermometer, Thermostat
• Topology: ADC, Multiplexer, Register Bank
• Sensor Type: External & Internal
• Sensing Temperature: -55°C ~ 125°C, External Sensor
• Output Type: I²C™/SMBus™
• Output Alarm: Yes
• Output Fan: No
• Voltage - Supply: 3 V ~ 5.5 V
• Operating Temperature: -55°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 16-QSOP
• Full Temp Accuracy: +/- 5 C
• Digital Output - Bus Interface: Serial (2-Wire)
• Digital Output - Number Of Bits: 7 bit + Sign
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 55 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2°C Accurate Remote/Local Temperature
Sensor with SMBus Serial Interface
The MAX6690 is a temperature sensor that communi-
cates through an SMBus/I
µP in thermal-management applications. Essentially an
11-bit serial analog-to-digital converter (ADC) with a
sophisticated front end, the MAX6690 measures the
change in diode voltage at different current levels to cal-
culate temperature. It contains a current source, a multi-
plexer, an ADC, an SMBus interface, and associated
control logic (Figure 1). Temperature data from the ADC
is loaded into data registers, where it is automatically
compared with data previously stored in four
over/undertemperature alarm registers.
The ADC is an averaging type that integrates over a
60ms period (each channel, typically, in the 8-bit “lega-
cy” mode), with excellent noise rejection.
The multiplexer automatically steers bias currents
through the remote and local diodes. The ADC and
associated circuitry measure their forward voltages and
compute their temperatures. Both channels are auto-
matically converted once the conversion process has
started, either in free-running or single-shot mode. If
one of the two channels is not used, the device still per-
forms both measurements, and the user can ignore the
results of the unused channel. If the remote-diode
channel is unused, connect DXP to DXN rather than
leave the pins open.
The DXN input is biased at 1V
internal diode to set up the ADC inputs for a differential
measurement. The worst-case DXP-DXN differential
input voltage range is 0.28V to 0.9V.
Excess resistance in series with the remote diode caus-
es about +1/2°C error per ohm when the parasitic resis-
tance cancellation mode is not being used. When the
parasitic resistance cancellation mode is being used,
excess resistance of up to 100Ω does not cause any
discernable error. A 200µV offset voltage forced on
DXP-DXN causes about 1°C error.
A conversion sequence consists of a local temperature
measurement and a remote-temperature measurement.
Each time a conversion begins, whether initiated auto-
matically in the free-running autoconvert mode
(RUN/STOP = 0) or by writing a “One-Shot” command,
both channels are converted, and the results of both
measurements are available after the end of conver-
sion. A BUSY status bit in the status byte shows that the
device is actually performing a new conversion; howev-
er, even if the ADC is busy, the results of the previous
conversion are always available.
6
_______________________________________________________________________________________
A/D Conversion Sequence
Detailed Description
2
C-compatible interface with a
ADC and Multiplexer
BE
above ground by an
The MAX6690 can directly measure the die tempera-
ture of CPUs and other ICs having on-board tempera-
ture-sensing diodes as shown in the Typical Operating
Circuit , or it can measure the temperature of a discrete
diode-connected transistor. For best accuracy, the dis-
crete transistor should be a small-signal device with its
collector and base connected together. Accuracy has
been experimentally verified for all of the devices listed
in Table 1.
The transistor must be a small-signal type with a rela-
tively high forward voltage; otherwise, the A/D input
voltage range can be violated. The forward voltage
must be >0.28V at 10µA; check to ensure this is true at
the highest expected temperature. The forward voltage
must be <0.9V at 100µA; check to ensure this is true at
the lowest expected temperature. Large power transis-
tors don’t work at all. Also, ensure that the base resis-
tance is <100Ω. Tight specifications for forward-current
gain (+50 to +150, for example) indicate that the manu-
facturer has good process controls and that the
devices have consistent VBE characteristics.
For heat-sink mounting, the 500-32BT02-000 thermal
sensor from Fenwal Electronics is a good choice. This
device consists of a diode-connected transistor, an alu-
minum plate with screw hole, and twisted-pair cable
(Fenwal Inc., Milford, MA, 508-478-6000).
Thermal mass can significantly affect the time required
for a temperature sensor to respond to a sudden
change in temperature. The thermal time constant of
the 16-pin QSOP package is about 140s in still air. For
the junction temperature of a MAX6690 in still air to set-
tle to within +1°C after a sudden +100°C change in air
temperature, about five time constants or 12 minutes
are required. However, the MAX6690 is not intended to
Table 1. Remote-Sensor Transistor
Manufacturers
Note: Transistors must be diode connected (base shorted to
collector).
Central Semiconductor (USA)
Fairchild Semiconductor (USA)
ON Semiconductor (USA)
Rohm Semiconductor (USA)
Samsung (Korea)
Siemens (Germany)
Zetex (England)
MANUFACTURER
Thermal Mass and Self-Heating
Remote-Diode Selection
CMPT3904
2N3904, 2N3906
2N3904, 2N3906
SST3904
KST3904-TF
SMBT3904
FMMT3904CT-ND
MODEL NO.