C1632C102K5RACTU Kemet, C1632C102K5RACTU Datasheet - Page 6

• Manufacturer Part Number: C1632C102K5RACTU
• Description: CAP 4-ARRAY 1000PF 50V X7R 1632
• Manufacturer: Kemet
• Series: C1632r

Specifications of C1632C102K5RACTU

• Capacitance: 1000pF
• Voltage - Rated: 50V
• Dielectric Material: Ceramic
• Number Of Capacitors: 4
• Circuit Type: Isolated
• Temperature Coefficient: X7R
• Tolerance: ±10%
• Mounting Type: Surface Mount
• Package / Case: 0612 (1632 Metric)
• Height: 0.053" (1.35mm)
• Size / Dimension: 0.126" L x 0.063" W (3.20mm x 1.60mm)
• Voltage Rating: 50 Volts
• Number Of Elements: 4
• Operating Temperature Range: - 55 C to + 125 C
• Termination Style: SMD/SMT
• Dimensions: 3.2 mm L x 1.6 mm W x 2 mm H
• Product: Ceramic Capacitor Arrays
• Capacitance Tolerance: ± 10%
• Capacitor Case Style: 0612
• Capacitor Mounting: SMD
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: C1632C102K5RAC; C1632C102K5RAC7800

SMD MLCCs – Capacitor Array, C0G Dielectric, 10VDC-200VDC, (Commercial & Automotive Grade)
Table 4 – Performance & Reliability: Test Methods and Conditions
Storage and Handling
Ceramic chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other
environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term
storage. In addition, packaging materials will be degraded by high temperature – reels may soften or warp, and tape peel force may
increase. KEMET recommends that maximum storage temperature not exceed 40 degrees C, and maximum storage humidity not
exceed 70% relative humidity. In addition, temperature fluctuations should be minimized to avoid condensation on the parts, and
atmospheres should be free of chlorine and sulfur bearing compounds. For optimized solderability, chip stock should be used promptly,
preferably within 1.5 years of receipt.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 [phone] • www.kemet.com
Resistance to Solvents
High Temperature Life
Temperature Cycling
Moisture Resistance
Mechanical Shock
Terminal Strength
Biased Humidity
Thermal Shock
Solderability
Storage Life
Board Flex
Stress
MIL-STD-202 Method 108/
MIL-STD-202 Method 106
MIL-STD-202 Method 108
MIL-STD-202 Method 103
MIL-STD-202 Method 107
MIL-STD-202 Method 213
MIL-STD-202 Method 215
JESD22 Method JA-104
Reference
JIS-C-6429
JIS-C-6429
J-STD-002
EIA-198
Appendix 1, Note: Force of 1.8kg for 60 seconds.
Appendix 2, Note: 2mm (min) for all except 3mm for C0G.
Magnification 50X. Conditions:
1000 Cycles (-55°C to +125°C), Measurement at 24 hrs. +/- 2 hrs after test conclusion.
Load Humidity: 1000 hours 85°C/85%RH and Rated Voltage. Add 100K ohm resistor. Measurement
at 24 hrs. +/- 2 hrs after test conclusion.
Low Volt Humidity: 1000 hours 85°C/85%RH and 1.5V. Add 100K ohm resistor.
Measurement at 24 hrs. +/- 2 hrs after test conclusion.
t = 24 hours/cycle. Steps 7a & 7b not required. Unpowered.
Measurement at 24 hrs. +/- 2 hrs after test conclusion.
-55°C/+125°C. Note: Number of cycles required-300, Maximum transfer time-20 seconds, Dwell
time-15 minutes. Air-Air.
1000 hours at 125°C (85°C for X5R, Z5U and Y5V) with 2X rated voltage applied.
150°C, 0VDC, for 1000 Hours.
Figure 1 of Method 213, Condition F.
Add aqueous wash chemical - OKEM Clean or equivalent.
a) Method B, 4 hrs @ 155°C, dry heat @ 235°C
b) Method B @ 215°C category 3
c) Method D, category 3 @ 260°C
Test or Inspection Method
C1016-2 • 5/16/2011
6 6