MIC9131BM Micrel Inc, MIC9131BM Datasheet
MIC9131BM
Specifications of MIC9131BM
Available stocks
Related parts for MIC9131BM
MIC9131BM Summary of contents
Page 1
MIC9131 General Description The MIC9131 is a current-mode PWM controller that efficiently converts –48V telecom voltages to logic levels. The MIC9131 features a high voltage start-up circuit that allows the device to be connected to input voltages as high as ...
Page 2
... MIC9131 Ordering Information Part Number Standard Pb-Free MIC9131BM MIC9131YM MIC9131BQS MIC9131YQS Pin Configuration Pin Description Pin Number Pin Name 1 LINE 2 VCC 3 RBIAS 4 OSC 5 SYNC 6 COMP CPWR 9 VBIAS AGND UVLO 14 ISNS 15 PGND 16 OUT M9999-080206 Max. Duty Cycle Junction Temp. Range 75% -40° ...
Page 3
MIC9131 Absolute Maximum Ratings Line Input Voltage (V ) ......................................... +190V LINE V Input Voltage (V ) .............................................. +19V CC CC Current Sense Input Voltage (V ISNS Enable Voltage (V ) ............................ –0 Feedback Input Voltage (V ...
Page 4
MIC9131 Parameter Condition Preregulator Input Leakage Current V LINE V Gate Lockout ( GLO(ON) LINE V Gate Lockout Hysteresis V CC LINE (ΔV ) GLO V Pre-Regulator Off ( PR(OFF) LINE V Pre-Regulator Hysteresis ...
Page 5
MIC9131 Typical Characteristics Oscillator Frequency vs. V Voltage CC 0.3 0.2 0.1 0.0 -0 -0.2 F =200kHz -0.3 OSC (NOM =9.47K -0 =470pF -0 ...
Page 6
MIC9131 V vs. V BIAS CC 5.012 R = 560K B IAS 5.010 5.008 5.006 5.004 5.002 5.000 4.998 ( Turn On/Off Thresholds CC vs. Temperature ...
Page 7
MIC9131 ISNS Pin Source Current vs =560K B IAS 41.5 41 40.5 40 39 (V) CC August 2006 ISNS Pin Source Current vs. Temperature 45 R ...
Page 8
MIC9131 Functional Block Diagram FB COMP OSC 7 6 Error 1.2V Amplifier 40µA ISNS 14 VBIAS 9 0.82V 5V EN BIAS 10 REG RBIAS 3 1.21V 5V 4µ CPWR 8 Q VCC 2 LINE 1 Thermal Shutdown M9999-080206 ...
Page 9
MIC9131 Functional Description Micrel’s MIC9131 is a high voltage, high speed current mode switching power supply controller. It uses a BiC/DMOS pro- cess to achieve a high voltage input, low quiescent current and very fast internal delay times. The MIC9131 ...
Page 10
MIC9131 plied and the depletion FET, which is normally enabled allows current from V to charge the V bias capacitor. Once the voltage reaches the V enable threshold the gate drive is enabled and ...
Page 11
MIC9131 GND UVLO Undervoltage Lockout CC The V voltage is internally divided down and compared 1.21V internal bandgap reference turn-on threshold, it disables the ...
Page 12
MIC9131 P_OSCILLATOR CHARGE DISCHARGE Where t = 75ns DELAY OSCILLATOR OSCILLATOR × OUTPU S OSCILLATOR 4 The timing capacitor, C ...
Page 13
MIC9131 cycle of the gate drive output increases until the error ampli- fier takes control of the duty cycle. The soft start capacitor is discharged by an internal MOSFET in the MIC9131. The soft start circuit is activated by the ...
Page 14
MIC9131 Gate Drive Output GND 1:N Figure 10 The gate impedance of a MOSFET is capacitive and the power required to drive the gate is proportional to the charge required to turn on the MOSFET, the peak ...
Page 15
MIC9131 series resistance is 10K, for a 500kHz switcher, the maximum series resistance is 2K. Sensing Current with a Resistor The fast transition times of the current signal prohibit the use of inductive resistors. Standard wire wound power resistors will ...
Page 16
MIC9131 If the current sense transformer were not used, the sense resistor would dissipate 1.7 watts SENSE 164 SENSE I 5 SENSE × ...
Page 17
MIC9131 Error Amplifier The error amplifier is part of the voltage control loop of the power supply. The FB pin is the inverting input to the error amplifier. The non-inverting input is internally connected to a 2.5V reference. The output ...
Page 18
MIC9131 Package Information M9999-080206 16-Pin SOP (M) 16-Pin QSOP (QS) 18 Micrel, Inc. August 2006 ...
Page 19
... MIC9131 MICREL INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA + 1 (408) 944-0800 TEL This information furnished by Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a signifi ...