SC174MLTRT Semtech, SC174MLTRT Datasheet
SC174MLTRT
Specifications of SC174MLTRT
Available stocks
Related parts for SC174MLTRT
SC174MLTRT Summary of contents
Page 1
... EcoSpeed Regulator with Optional Ultrasonic Power Save Description The SC174 is an integrated, synchronous 4A EcoSpeed step-down regulator, which incorporates Semtech’s advanced, patented adaptive on-time architecture to achieve best-in-class performance in dynamic point-of- load applications. The input voltage range 5.5V with a programmable output voltage from 0.75V ...
Page 2
... Date Code (Example: 0952) xxxx = Semtech Lot Number (Example: 3901) © 2010 Semtech Corporation Ordering Information Device SC174MLTRT SC174EVB VDD Notes: AGND 1) Available in tape and reel packaging only. A reel contains 3000 devices. TON 2) Available in lead-free packaging only. WEEE compliant and Halogen EN/PSV free ...
Page 3
... FB On-Time Threshold Frequency Programming Range FB Input Bias Current © 2010 Semtech Corporation Recommended Operating Conditions Supply Input Voltage……………………………… 5.5V Maximum Continuous Output Current …………………… 4A Thermal Information -0 ...
Page 4
... Noise Immunity Delay Time Leakage Power Good On-Resistance Fault Protection Output Under-Voltage Fault Output Over-Voltage Fault Smart PowerSave Protection Threshold OV, UV Fault Noise Immunity Delay Over-Temperature Shutdown © 2010 Semtech Corporation < 125°C J Symbol Conditions Continuous Mode V =5V, V =3V, R =200kΩ ...
Page 5
... BST Switch On resistance Internal Power MOSFETs Current Limit LX Leakage Current Switch Resistance Non-overlap time (1) Note: (1) Typical value from EVB, not ATE tested. © 2010 Semtech Corporation < 125°C J Symbol Conditions EN/PSV = VDD or 0V EN/PSV floating Valley Current Limit, VDD=5V Valley Current Limit, VDD=3V VIN=5 ...
Page 6
... On-time set input. Set the on-time by a series resistor to AGND 9 AGND Analog Ground. 10 VDD Input power for internal control circuit. Needs 1mF decoupling capacitor from this pin to AGND. Thermal pad for heatsinking purposes. Connect to ground plane using multiple vias. Not con- PAD nected internally. © 2010 Semtech Corporation SC174 . 6 ...
Page 7
... Block Diagram 10 VDD AGND Reference 9 Soft Start TON © 2010 Semtech Corporation PGOOD Control Gate Drive Control On-Time Generator Zero-Cross Valley Current Limit 1 VDD BST VIN VDD PGND ...
Page 8
... TON L : DS86C-B992AS-2R0N OUT 65.0 C :22 F OUT Forced Continuous Mode 60.0 Red:Vin = 3.5V Green: Vin = 4.0V 55.0 Blue: Vin = 5.0V 50 Output Current (A) © 2010 Semtech Corporation 3.340 3.331 3.323 3.314 3.306 3.297 3 4 1.215 1.210 1.205 1.200 1.195 3 4 1.210 1.208 1.205 1 ...
Page 9
... -2.0 BST IN -2.5 -3.0 -50 - Temperature (°C) © 2010 Semtech Corporation Start up waveform ( Channel 1: 500mV/Div, Channel 4: 2A/Div, Time: 0.5ms/Div 75 100 125 Load Transient Test ( Forced Continuous Conduction Mode OUT 2:5V/Div,Channel 4: 2A/Div, Time:10 s/Div) 75 100 125 Load Transient Test ( Forced Continuous Conduction Mode, L ...
Page 10
... High Side Switch On-State Resistance vs Temperature -40 - Temperature (°C) © 2010 Semtech Corporation Load Transient Test ( PSAVE Mode Enabled, L 50mV/Div, Channel 2:5V/Div,Channel 4:2A/Div,Time:20 s/Div 110 135 Load Transient Test ( PSAVE Mode Enabled, L 50mV/Div,Channel 2:5V/Div,Channel 4:2A/Div, Time:20 s/Div) Blue: VDD=3.0V Black: VDD=5.0V 85 110 135 Blue: VDD=3 ...
Page 11
... C OUT Figure 1 — PWM Control Method, V © 2010 Semtech Corporation The adaptive on-time is determined by an internal one- shot timer. When the one-shot is triggered by the out- put ripple, the device sends a single on-time pulse to the high-side MOSFET. The pulse period is determined by ...
Page 12
... V = 0.75V ⋅ OUT R 2 © 2010 Semtech Corporation Enable and Power-save Inputs The EN/PSV input is used to enable or disable the switch- V ing regulator. When EN/PSV is low (grounded), the switch LPF OUT ing regulator is off and in its lowest power state. When Q1 L off, the output power switches are tri-stated. When EN/ ...
Page 13
... Smart Power Save Protection Active loads may leak current from a higher voltage into the switcher output. Under light load conditions with © 2010 Semtech Corporation power save enabled, this can force V and reach the over-voltage threshold, resulting in a hard shutdown. Smart power save prevents this condition. ...
Page 14
... Typical soft start ramp time is 0.85ms. © 2010 Semtech Corporation During soft start the regulator turns off the low-side MOSFET on any cycle if the inductor current falls to zero. ...
Page 15
... The desired switching frequency is 800kHz which results from using components selected for optimum size and cost . A resistor ( used to program the on-time (indirectly TON © 2010 Semtech Corporation setting the frequency) using the following equation. Calculating R R =50kW, we use R TON ) is the highest speci- ...
Page 16
... Since this 2% error comes from 1/2 of the ripple voltage, the allowable ripple is 4%, or 40mV for a 1V out- put. © 2010 Semtech Corporation The maximum ripple current of 0.511A creates a ripple voltage across the ESR. The maximum ESR value allowed is shown by the following equations. ...
Page 17
... This form of instability can usually be avoided by providing the FB pin with a smooth, clean ripple signal that is at least 10mVp-p, which may dictate the need to © 2010 Semtech Corporation increase the ESR of the output capacitors also im- perative to provide a proper PCB layout as discussed in the Layout Guidelines section ...
Page 18
... C =39pF can be used for many output volt ages and loads. © 2010 Semtech Corporation Output Voltage Dropout The output voltage adjustable range for continuous- conduction operation is limited by the fixed 320ns (typi- cal) minimum off-time. When working with low input voltages, the duty-factor limit must be calculated using worst-case values for on and off times ...
Page 19
... PVIN pin, the device is designed and guaranteed to tolerate the short transient voltages, of maximum 20ns duration, that will appear on the LX pin due to the © 2010 Semtech Corporation deadtime diode conduction, as long as the transient volt- age on PVIN is less than 6.0V. The time duration of the transient LX pin voltage is measured on the voltage por- tion which is either over 6 ...
Page 20
... It is recommended to get the power from VIN through an RC filtering network consisted of R1, C6 and C10. The value of R1 can be between 3.01W and 10W and the capacitance of C10 should be above 1mF. C6, with a value of 1nF, is the high frequency filtering capacitor. The © 2010 Semtech Corporation ...
Page 21
... R6 in series with C9 is connected to the LX pin (through the via) to the power ground the coupling capacitor which injects the ramp signal generated the FB pin of the SC174 the pull up resistor for the PGOOD pin. © 2010 Semtech Corporation 21 ...
Page 22
... VIN © 2010 Semtech Corporation V IN C11 C1 PGND AGND PGND AGND Top Layer C6 R1 C10 AGND R2 EN/PSV Inner Layer 1 22 ...
Page 23
... VIN PGND © 2010 Semtech Corporation PGND 5 6 AGND AGND SC174 Inner Layer 2 Bottom Layer 23 ...
Page 24
... Application Circuit: Buck Converter with 1.2V out and load current (Vin=5V) VIN+ C101 C1 10uF/6.3V 0.1uF/6.3V VIN- VOUT 22uF/6.3v 22uF/6.3v VOUT- 38p FB Application Circuit: Buck Converter with 3.3V out and load current (Vin=5V) © 2010 Semtech Corporation 1uF/6. 2.0uH R6 9.09k R4 100k R5 C10 2.49k C18 68pF C19 R2 ...
Page 25
... Outline Drawing - MLPD-10 3x3 A PIN 1 INDICATOR (LASER MARK) aaa C 1 LxN E D/2 NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS TERMINALS. © 2010 Semtech Corporation D B DIM aaa bbb A SEATING PLANE bxN bbb DIMENSIONS INCHES MILLIMETERS ...
Page 26
... THERMAL VIAS IN THE LAND PATTERN OF THE EXPOSED PAD SHALL BE CONNECTED TO A SYSTEM GROUND PLANE. SHALL BE CONNECTED TO A SYSTEM GROUND PLANE. FAILURE MAY COMPROMISE THE THERMAL AND/OR FAILURE MAY COMPROMISE THE THERMAL AND/OR FUNCTIONAL PERFORMANCE OF THE DEVICE. FUNCTIONAL PERFORMANCE OF THE DEVICE. © 2010 Semtech Corporation K DIM C K DIMENSIONS G ...
Page 27
... PLICATIONS IS UNDERSTOOD TO BE UNDERTAKEN SOLELY AT THE CUSTOMER’S OWN RISK. Should a customer purchase or use Semtech products for any such unauthorized application, the customer shall indemnify and hold Semtech and its officers, em- ployees, subsidiaries, affiliates, and distributors harmless against all claims, costs damages and attorney fees which could arise. ...