LTC3615EFE-1#TRPBF Linear Technology, LTC3615EFE-1#TRPBF Datasheet - Page 21

• Manufacturer Part Number: LTC3615EFE-1#TRPBF
• Description: IC REG SYNC BUCK 3A 24TSSOP
• Manufacturer: Linear Technology
• Type: Step-Down (Buck)r

Specifications of LTC3615EFE-1#TRPBF

• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 2
• Voltage - Output: 0.6 ~ 5.5 V
• Current - Output: 3A
• Frequency - Switching: 400kHz ~ 4MHz
• Voltage - Input: 2.25 ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 24-TSSOP Exposed Pad, 24-eTSSOP, 24-HTSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -

APPLICATIONS INFORMATION
The LTC3615 allows the user to control the slew rate of
the switching node SW by using the SRLIM pin. Tying this
pin to ground selects the fastest slew rate. The slowest
slew rate is selected when the pin is open. Connecting a
resistor (between 10k to 100k) from SRLIM pin to ground
adjusts the slew rate between the maximum and minimum
values. The reduced dV/dt of the switch node results in a
signifi cant reduction of the supply and ground ringing, as
well as lower radiated EMI. See Figure 7a and the Typical
Performance Characteristics section for examples.
Reducing the slew rate causes a trade-off between ef-
fi ciency and low EMI (see Figure 7b).
Particular attention should be used with very high switching
frequencies. Using the slowest slew rate (SRLIM open)
can reduce the minimum duty cycle capability.
Soft-Start
The RUNx pins provide a means to shut down each chan-
nel of the LTC3615. Pulling both pins below 0.3V places
the LTC3615 in a low quiescent current shutdown state
(I
After enabling the LTC3615 by bringing either one or both
RUNx pins above the threshold, the enabled channels enter
a soft-start-up state. The type of soft-start behavior is set
by the TRACK/SSx pins. The soft-start cycle begins with
an initial discharge pulse pulling down the TRACK/SSx
Q
(7a) Slew Rate of Rising Edge at SW1/2 vs SRLIM Resistor
< 1μA).
1V/DIV
V
V
I
OUT
IN
OUT
= 3.3V
= 1A
= 1.8V
40.2k
2ns/DIV
SGND OR SV
SRLIM =
OPEN
IN
100k
3615 F07a
Figure 7. Slew Rate and the SRLIM Resistor
pin to SGND and discharging the external capacitor C
(see Figure 3).
The initial discharge is adequate to discharge capacitors
up to 33nF . If a larger capacitor is required, connect the
external soft-start resistor R
discharge the capacitor.
1. Tying this pin to SV
2. If a longer soft-start period is desired, it can be set ex-
3. The TRACK/SSx pin can be used to track the output
circuit. This circuit ramps the output voltage to the fi nal
value within 1ms.
ternally with a resistor and capacitor on the TRACK/SSx
pins as shown in Figure 3. The voltage applied at the
TRACK/SSx pins sets the value of the internal refer-
ence at V
external soft-start duration can be calculated by using
the following equation:
voltage of another supply.
Regardless of either the internal or external soft-start
state, the MODE pin is ignored during start-up and the
regulator defaults to pulse-skipping mode. In addition,
the PGOODx pin is kept low, and the frequency foldback
function is disabled.
t
SS
=
(7b) Effi ciency vs SRLIM Resistor Programming
R
SS
FB
92
91
90
89
88
87
86
85
82
84
83
2.25
•
until TRACK/SSx is pulled above 0.6V. The
V
I
FCM
C
OUT
40.2k
OUT
LTC3615/LTC3615-1
SS
= 1A
= 1.8V
•
3.06
In
IN
⎛
⎝ ⎜
20k
SV
selects the internal soft-start
V
3.88
IN
IN
SS
(V)
SV
– . 0 6
OPEN
IN
to the RUN pin to fully
GND OR SV
4.69
V
⎞
⎠ ⎟
IN
3615 07b
5.50
21
3615fa
SS