LTC1159CG-5#PBF Linear Technology, LTC1159CG-5#PBF Datasheet - Page 7

• Manufacturer Part Number: LTC1159CG-5#PBF
• Description: IC SW REG STEP-DOWN 5V 20-SSOP
• Manufacturer: Linear Technology
• Type: Step-Down (Buck)r

Specifications of LTC1159CG-5#PBF

• Internal Switch(s): No
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 5V
• Current - Output: 50mA
• Frequency - Switching: 250kHz
• Voltage - Input: 4 ~ 40 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 20-SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -

OPERATIO
APPLICATIO S I FOR ATIO
increases, the output voltage decreases slightly. This causes
the output of the gain stage to increase the current com-
parator threshold, thus tracking the load current.
The sequence of events for Burst Mode operation is very
similar to continuous operation with the cycle interrupted
by the voltage comparator. When the output voltage is at or
above the desired regulated value, the P-channel MOSFET
is held off by comparator V and the timing capacitor con-
tinues to discharge below V
discharges past V
the internal SLEEP line to go low and the N-channel MOSFET
to turn off.
The circuit now enters sleep mode with both power
MOSFETs turned off. In sleep mode, much of the circuitry
The LTC1159 Compared to the LTC1148/LTC1149
Families
The LTC1159 family is closest in operation to the LTC1149
and shares much of the applications information. In addi-
tion to reduced quiescent and shutdown currents, the
LTC1159 adds an internal switch which allows the driver
and control sections to be powered from an external
source for higher efficiency. This change affects Power
MOSFET Selection, EXTV
Information About LTC1159 Adjustable Applications, and
Efficiency Considerations found in this section.
The basic LTC1159 application circuit shown in Figure 1
is limited to a maximum input voltage of 30V due to
MOSFET breakdown. If the application does not require
greater than 18V operation, then the LTC1148 or
LTC1148HV should be used. For higher input voltages
where quiescent and shutdown current are not critical, the
LTC1149 may be a better choice since it is set up to drive
standard threshold MOSFETs.
R
R
LTC1159 current comparator has a threshold range that
extends from a minimum of 0.025V/R
SENSE
SENSE
is chosen based on the required output current. The
Selection for Output Current
TH2
U
U
, voltage comparator S trips, causing
(Refer to Functional Diagram)
U
CC
TH1
Pin Connection, Important
. When the timing capacitor
W
SENSE
to a maximum
U
is turned off, dropping the supply current from several
milliamps (with the MOSFETs switching) to 300 A. When
the output capacitor has discharged by the amount of
hysteresis in comparator V, the P-channel MOSFET is
again turned on and this process repeats. To avoid the
operation of the current loop interfering with Burst Mode
operation, a built-in offset is incorporated in the gain stage.
To prevent both the external MOSFETs from being turned
on at the same time, feedback is incorporated to sense the
state of the driver output pins. Before the N-gate output can
go high, the P-drive output must also be high. Likewise, the
P-drive output is prevented from going low when the
N-gate output is high.
of 0.15V/R
the peak of the inductor ripple current, yielding a maximum
output current I
peak-to-peak ripple current. For proper Burst Mode opera-
tion, I
current comparator threshold.
Since efficiency generally increases with ripple current,
the maximum allowable ripple current is assumed, i.e.,
I
Operating Frequency). Solving for R
a margin for variations in the LTC1159 and external
component values yields:
A graph for selecting R
current is given in Figure 2. The LTC1159 series works well
with values of R
The load current below which Burst Mode operation com-
mences, I
both track I
I
RIPPLE(P-P)
SC(PK)
R
SENSE
RIPPLE(P-P)
can be predicted from the following equations:
BURST
SENSE
MAX
=
= 0.025V/R
I
100
MAX
. Once R
, and the peak short-circuit current, I
MAX
LTC1159-3.3/LTC1159-5
SENSE
must be less than or equal to the minimum
. The current comparator threshold sets
m
equal to the peak value less half the
from 0.02 to 0.2 .
SENSE
SENSE
SENSE
has been chosen, I
(see C
versus maximum output
T
SENSE
and L Selection for
LTC1159
and allowing
BURST
SC(PK)
7
and
,