MAX1522EUT+T Maxim Integrated Products, MAX1522EUT+T Datasheet - Page 8

• Manufacturer Part Number: MAX1522EUT+T
• Description: IC SIMPLE BOOST CNTRLR SOT23-6
• Manufacturer: Maxim Integrated Products
• Type: Step-Up (Boost), Flyback, Sepicr

Specifications of MAX1522EUT+T

• Internal Switch(s): No
• Synchronous Rectifier: No
• Number Of Outputs: 1
• Voltage - Output: 2.5 ~ 100 V
• Current - Output: 1A
• Frequency - Switching: 1MHz
• Voltage - Input: 2.5 ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: SOT-23-6
• Power - Output: 696mW
• Output Voltage: 2.5 V to 100 V
• Output Current: 1 A
• Input Voltage: 2.5 V to 5.5 V
• Mounting Style: SMD/SMT
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Simple SOT23 Boost Controllers
Figure 2. MAX1524 Standard Operating Circuit
For CCM, the ideal inductor value is given by:
If L
est value, either higher or lower. Nominal values within
50% are acceptable. Values lower than ideal will have
slightly higher peak inductor current; values greater
than ideal will have slightly lower peak inductor current.
Due to the MAX1522/MAX1523/MAX1524s’ high switch-
ing frequencies, inductors with a ferrite core or equiva-
lent are recommended. Powdered iron cores are not
recommended due to their high losses at frequencies
over 50kHz.
The saturation rating of the selected inductor should
meet or exceed the calculated value for I
although most coil types can be operated up to 20%
over their saturation rating without difficulty. In addition
to the saturation criteria, the inductor should have as
low a series resistance as possible. The power loss in
the inductor resistance is approximately given by:
In CCM, to provide stable operation and to control out-
put sag to less than 0.5%, the output bulk capacitance
should be greater than:
8
IDEAL
_______________________________________________________________________________________
is not a standard value, choose the next-clos-
P
LR
L
IDEAL
≅
⎛
⎜
⎝
I
LOAD
3.3V ±10%
=
INPUT
V
IN TYP
×
OFF
(
(
V
Output Capacitor Selection
0.1µF
. 0 3
V
IN
OUT
C3
ON
)
×
×
10Ω
I
PEAK
R3
+
t
ON TYP
V
D
Inductor Selection
(
)
⎞
⎟
⎠
2
6
3
4
)
×
V
SET
SHDN
R L
CC
MAX1524
PEAK
,
GND
EXT
FB
5
2
1
C1
10µF
6.3V
To properly control peak inductor current during the
3.2ms soft-start, the output bulk capacitance should be
less than:
where t
Because the MAX1522/MAX1523/MAX1524 are volt-
age-mode devices (and therefore do not require an
expensive current-sense resistor), cycle-to-cycle stabil-
ity is obtained from the output capacitor’s equivalent
series resistance (ESR). Choose an output capacitor
with actual ESR greater than:
Additionally, to control peak inductor current during soft-
start, the output capacitor’s ESR should be greater
than:
Usually, this prevents the use of ceramic capacitors in
CCM applications. Alternatives include tantalum, elec-
trolytic, and organic types such as Sanyo’s POSCAP.
The output capacitor must also be rated to withstand
the output voltage and the output ripple current, which
is equivalent to I
DC designs is dominated by capacitor ESR, a capaci-
Q1
FDC633N
SS
L1
33µH
CR43-3R3
C
= 3.2ms.
C
OUT MAX
ESR
CRS01
OUT MIN
ESR
D1
33.2kΩ
100kΩ
(
COUT
1%
(
PEAK
1%
R1
COUT
R2
)
)
=
. Since output ripple in boost DC-
>
=
I
>
LOAD MAX
C
I
LOAD MAX
60 10
OUT
C
100pF
0 005
L
FF
.
×
V
(
(
OUT
×
−
×
I
LOAD MAX
3
)
V
V
×
)
×
OUT
IN MIN
C2
33µF
10TPA33M
×
I
t
PEAK
(
V
SS
t
(
ON
FB
)
OUTPUT
)
5V