B32674D8474K EPCOS Inc, B32674D8474K Datasheet - Page 24

• Manufacturer Part Number: B32674D8474K
• Description: CAP .47UF 10% 875V METAL POLYPRO
• Manufacturer: EPCOS Inc
• Series: MKP B32674r

Specifications of B32674D8474K

• Capacitance: 0.47µF
• Tolerance: ±10%
• Lead Spacing: 1.083" (27.50mm)
• Voltage - Ac: 400V
• Voltage - Dc: 875V
• Dielectric Material: Polypropylene, Metallized
• Esr (equivalent Series Resistance): 22.9 mOhm
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Through Hole
• Package / Case: Radial
• Size / Dimension: 1.240" L x 0.433" W (31.50mm x 11.00mm)
• Height: 0.748" (19.00mm)
• Termination: PC Pins
• Features: AC and Pulse
• Voltage Rating: 875 Volts
• Esr: 14 mOhms
• Termination Style: Radial
• Dimensions: 11 mm W x 31.5 mm L x 19 mm H
• Operating Temperature Range: - 55 C to + 85 C
• Product: Metallized Polypropylene Capacitors
• Tolerance (+ Or -): 10%
• Temp Coeff (dielectric): PLYP
• Mounting Style: Through Hole
• Construction: Radial
• Failure Rate: Not Required
• Seated Plane Height: 19mm
• Product Diameter (mm): Not Requiredmm
• Product Height (mm): 19mm
• Product Depth (mm): 11mm
• Product Length (mm): 31.5mm
• Lead Spacing (nom): 27.5mm
• Lead Diameter (nom): 0.8mm
• Operating Temp Range: -40C to 100C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 495-2938; B32674D8474K000

1.3
Permissible heat exposure loads on film capacitors are primarily characterized by the upper cate-
gory temperature T
can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical
characteristics. For short exposures (as in practical soldering processes) the heat load (and thus
the possible effects on a capacitor) will also depend on other factors like:
The overheating associated with some of these factors can usually be reduced by suitable coun-
termeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced
cooling process may possibly have to be included.
EPCOS recommends the following conditions:
Uncoated capacitors
For uncoated MKT capacitors with lead spacings 10 mm (B32560/B32561) the following mea-
sures are recommended:
Please read Cautions and warnings and
Important notes at the end of this document.
Pre-heating temperature and time
Forced cooling immediately after soldering
Terminal characteristics:
diameter, length, thermal resistance, special configurations (e.g. crimping)
Height of capacitor above solder bath
Shadowing by neighboring components
Additional heating due to heat dissipation by neighboring components
Use of solder-resist coatings
Pre-heating with a maximum temperature of 110 C
Temperature inside the capacitor should not exceed the following limits:
When SMD components are used together with leaded ones, the leaded film capacitors should
not pass into the SMD adhesive curing oven. The leaded components should be assembled af-
ter the SMD curing step.
Leaded film capacitors are not suitable for reflow soldering.
pre-heating to not more than 110 C in the preheater phase
rapid cooling after soldering
MKP/MFP 110 C
MKT 160 C
General notes on soldering
B32674 ... B32678
MKP DC link
max
. Long exposure to temperatures above this type-related temperature limit
high power series
Page 24 of 32