OPTOCOUPLER LOG-OUT 2CH 8-DIP

HCPL2630

Manufacturer Part NumberHCPL2630
DescriptionOPTOCOUPLER LOG-OUT 2CH 8-DIP
ManufacturerFairchild Optoelectronics Group
HCPL2630 datasheet
 

Specifications of HCPL2630

Voltage - Isolation2500VrmsNumber Of Channels2, Unidirectional
Current - Output / Channel50mAData Rate10Mbps
Propagation Delay High - Low @ If45ns @ 7.5mACurrent - Dc Forward (if)30mA
Input TypeDCOutput TypeOpen Collector
Mounting TypeThrough HolePackage / Case8-DIP
Lead Free Status / RoHS StatusLead free / RoHS CompliantOther namesHCPL-2630GI
HCPL2630GI
HCPL2630QT
MCL2630
MCL2630GI
MCL2630QT
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
Page 4/12

Download datasheet (632Kb)Embed
PrevNext
Electrical Characteristics
Transfer Characteristics
(T
A
Symbol
DC Characteristics
I
HIGH Level Output Current
OH
V
LOW Level Output Current
OL
I
Input Threshold Current
FT
Isolation Characteristics
(T
A
Symbol
Characteristics
I
Input-Output Insulation
I-O
Leakage Current
V
Withstand Insulation Test
ISO
Voltage
R
Resistance (Input to Output)
I-O
C
Capacitance (Input to Output)
I-O
*All Typicals at V
= 5V, T
= 25°C
CC
A
Notes:
1. The V
supply to each optoisolator must be bypassed by a 0.1µF capacitor or larger. This can be either a ceramic
CC
or solid tantalum capacitor with good high frequency characteristic and should be connected as close as possible
to the package V
and GND pins of each device.
CC
2. Each channel.
3. Enable Input – No pull up resistor required as the device has an internal pull up resistor.
4. t
– Propagation delay is measured from the 3.75mA level on the HIGH to LOW transition of the input current
PLH
pulse to the 1.5 V level on the LOW to HIGH transition of the output voltage pulse.
5. t
– Propagation delay is measured from the 3.75mA level on the LOW to HIGH transition of the input current
PHL
pulse to the 1.5 V level on the HIGH to LOW transition of the output voltage pulse.
6. t
– Rise time is measured from the 90% to the 10% levels on the LOW to HIGH transition of the output pulse.
r
7. t
– Fall time is measured from the 10% to the 90% levels on the HIGH to LOW transition of the output pulse.
f
8. t
– Enable input propagation delay is measured from the 1.5V level on the HIGH to LOW transition of the input
ELH
voltage pulse to the 1.5V level on the LOW to HIGH transition of the output voltage pulse.
9. t
– Enable input propagation delay is measured from the 1.5V level on the LOW to HIGH transition of the input
EHL
voltage pulse to the 1.5V level on the HIGH to LOW transition of the output voltage pulse.
10. CM
– The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the
H
HIGH state (i.e., V
> 2.0V). Measured in volts per microsecond (V/µs).
OUT
11. CM
– The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the
L
LOW output state (i.e., V
OUT
12. Device considered a two-terminal device: Pins 1, 2, 3 and 4 shorted together, and Pins 5, 6, 7 and 8 shorted
together.
©2005 Fairchild Semiconductor Corporation
6N137, HCPL2601, HCPL2611, HCPL2630, HCPL2631 Rev. 1.0.8
(Continued)
= -40 to +85°C unless otherwise specified)
Test Conditions
V
= 5.5V, V
= 5.5V,
CC
O
(2)
I
= 250µA, V
= 2.0V
F
E
V
= 5.5V, I
= 5mA, V
CC
F
E
(2)
I
= 13mA
CL
V
= 5.5V, V
= 0.6V, V
CC
O
E
I
= 13mA
OL
= -40°C to +85°C unless otherwise specified.)
Test Conditions
Relative humidity = 45%,
T
= 25°C, t = 5s,
A
(12)
V
= 3000 VDC
I-O
RH < 50%, T
= 25°C,
A
≤ 2µA, t = 1 min.
(12)
I
I-O
(12)
V
= 500V
I-O
(12)
f = 1MHz
< 0.8V). Measured in volts per microsecond (V/µs).
4
Min.
Typ.*
Max.
100
= 2.0V,
.35
0.6
= 2.0V,
3
5
Min.
Typ.*
Max.
1.0*
2500
12
10
0.6
www.fairchildsemi.com
Unit
µA
V
mA
Unit
µA
V
RMS
pF