HCPL-2630-000E Avago Technologies US Inc., HCPL-2630-000E Datasheet - Page 7

• Manufacturer Part Number: HCPL-2630-000E
• Description: OPTOCPLR 2CH LOG-OUT 10MBD 8-DIP
• Manufacturer: Avago Technologies US Inc.
• Type: Logicr

Specifications of HCPL-2630-000E

• Package / Case: 8-DIP (0.300", 7.62mm)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 2, Unidirectional
• Current - Output / Channel: 50mA
• Data Rate: 10MBd
• Propagation Delay High - Low @ If: 50ns @ 7.5mA
• Current - Dc Forward (if): 20mA
• Input Type: DC
• Output Type: Open Collector
• Mounting Type: Through Hole
• Isolation Voltage: 3750 Vrms
• Maximum Continuous Output Current: 50 mA
• Maximum Fall Time: 0.01 us
• Maximum Forward Diode Current: 15 mA
• Minimum Forward Diode Voltage: 1.4 V
• Output Device: Logic Gate Photo IC
• Configuration: 2 Channel
• Maximum Baud Rate: 10 MBd(Typ)
• Maximum Forward Diode Voltage: 1.75 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Power Dissipation: 60 mW
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Package Type: 8-Pin DIP
• Special Features: 2 Channel
• No. Of Channels: 2
• Optocoupler Output Type: Logic Gate
• Input Current: 15mA
• Output Voltage: 7V
• Opto Case Style: DIP
• No. Of Pins: 8
• Common Mode Ratio: 10000
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-1475-5

Recommended Pb-free IR Profile
Regulatory Information
The 6N137, HCPL-26XX/06XX/46XX,
and HCNW137/26XX have been ap-
proved by the following organiza-
tions:
Insulation and Safety Related Specifications
Minimum External
Air Gap (External
Clearance)
Minimum External
Tracking (External
Creepage)
Minimum Internal
Plastic Gap
(Internal Clearance)
Minimum Internal
Tracking (Internal
Creepage)
Tracking Resistance
(Comparative
Tracking Index)
Isolation Group
Option 300 - surface mount classification is Class A in accordance with CECC 00802.
7
Parameter
NOTES:
THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX.
T
Note: Non-halide flux should be used.
T
T
smax
smax
smin
25
T
T
p
L
= 200 °C, T
150 - 200 °C
217 °C
t 25 °C to PEAK
3 °C/SEC. MAX.
60 to 180 SEC.
smin
PREHEAT
RAMP-UP
= 150 °C
t
L(101)
L(102)
Symbol
s
CTI
260 +0/-5 °C
TIME
8-pin DIP
(300 Mil)
t
t
L
Value
UL
Recognized under UL 1577, Com-
ponent Recognition Program, File
E55361.
CSA
Approved under CSA Component
Acceptance Notice #5, File CA
88324.
0.08
p
200
7.1
7.4
NA
IIIa
TIME WITHIN 5 °C of ACTUAL
PEAK TEMPERATURE
20-40 SEC.
60 to 150 SEC.
RAMP-DOWN
6 °C/SEC. MAX.
Value
0.08
SO-8
200
4.9
4.8
NA
IIIa
Widebody
(400 Mil)
Value
10.0
200
9.6
1.0
4.0
IIIa
Volts
Units
mm
mm
mm
mm
IEC/EN/DIN EN 60747-5-2
Approved under
IEC 60747-5-2:1997 + A1:2002
EN 60747-5-2:2001 + A1:2002
DIN EN 60747-5-2 (VDE 0884
(Option 060 and HCNW only)
Conditions
Measured from input terminals
to output terminals, shortest
distance through air.
Measured from input terminals
to output terminals, shortest
distance path along body.
Through insulation distance,
conductor to conductor, usually
the direct distance between the
photoemitter and photodetector
inside the optocoupler cavity.
Measured from input terminals
to output terminals, along
internal cavity.
DIN IEC 112/VDE 0303 Part 1
Material Group
(DIN VDE 0110, 1/89, Table 1)
Teil 2):2003-01